Fujitsu PRIMERGY RX200 S3 Options Manual Download Page 39 | Manualshive

Page: 39 / 57

background image

RX200 S3

Options Guide

39

Controllers in Non-Hot-Plug PCI Slots

Installing controllers

8.1

Installing controllers

Ê

Open the server as described in the

chapter “Preparation” on page 17

Removing the riser card holder

Figure 22: Removing the riser card holder

Ê

Grasp the riser card at the two green points labeled with “LIFT UP” and pull
it up and out.

Installing a controller

Ê

Please read the documentation supplied with the controller.

Ê

Plug any necessary cables onto the controller.

Ê

Remove the slot cover from the riser card holder.

I

Keep the slot cover for future use. If you remove the controller, you
must reinstall the slot cover to comply with EMC regulations (regula-
tions on electromagnetic compatibility) and to satisfy cooling require-
ments and fire protection measures.

«
...
37
38
39
40
41
...
»

Summary of Contents for PRIMERGY RX200 S3


























































Reviews:

No comments

Related manuals for PRIMERGY RX200 S3

NOP1840 PEP-Box

Brand: Newtec Pages: 96

eServer BladeCenter HS40 Type 8839

Brand: IBM Pages: 120

Brand: Kyocera Pages: 207

callpilot 1002rp

Brand: Avaya Pages: 150

Brand: NEC Pages: 10

HPE ProLiant DL580 Gen10

Brand: Hewlett Packard Enterprise Pages: 197

Brand: Asus Pages: 186

Brand: Cavalry Pages: 16

Brand: Xerox Pages: 2

StorageWorks E Series

Brand: HP Pages: 8

StorageWorks 9000s NAS

Brand: HP Pages: 7

StorageWorks NAS e7000 v2

Brand: HP Pages: 2

StorageWorks NAS e7000 v2

Brand: HP Pages: 70

StorageWorks 600 All-in-One

Brand: HP Pages: 58

StorageWorks All-in-One SB600c - Storage Blade

Brand: HP Pages: 60

T19 Hydro Server

Brand: BITMAIN Pages: 17

Brand: Meinberg Pages: 170

Brand: Eelectron Pages: 42

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands