Fujitsu PRIMEQUEST 440 System Design Manual Download

Page: 64 / 280

2-6

C122-B001-02EN

CHAPTER 2 General Hardware Configuration

2.2

System Board (SB)

CPUs, memory, various chipsets, and a DC-DC converter are mounted on the SB:

The PRIMEQUEST 480 main unit contains one to eight SBs, and the
PRIMEQUEST 440 main unit contains one to four SBs.

The SB contains one to four CPUs and one set (four modules) to eight sets (32
modules) of memory.

At least one CPU and one set of memory must be mounted on an SB that composes
a partition.

Note:

For details on the partition function, see

CHAPTER 8, "Partition."

Figure 2.4 SB

Table 2.2 SB specifications

Item

Specifications

Number of CPUs

1 to 4

Number of memory modules

DDR2-DIMM

4 to 32

(added in sets of four modules)

DIM

CPU

DC-DC converter

SB Power

SB Alarm

Location

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands

Fujitsu PRIMEQUEST 440, System Design Manual

Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands