Fujitsu PRIMEQUEST 440 System Design Manual Download

Page: 180 / 280

6-2

C122-B001-02EN

CHAPTER 6 Redundant Configuration

6.1

Redundancy of Components

Figure 6.1

shows components for which redundant configuration can be adopted.

Figure 6.1 General redundant configuration

(1) PRIMEQUEST 480

This part describes redundant configuration of the following components for the
PRIMEQUEST 480 family.

• System Board (SB)

From one to up to eight SBs can be mounted. Redundant configuration can be
adopted depending on the operation methods. For details, see

CHAPTER 8,

"Partition,"

and

CHAPTER 9, "Clustering."

An SB can have one to four IPF CPUs

and up to 8 set (32) memory boards (DIMMs).

Redundant configuration
is possible.

Redundant configuration is
possible depending on operation.

PRIMEQUEST

PCI_Box

PCIU

CPCB

XDI

XAI

GSWB

MMB

OPL

FAN TRAY

KVM

IOU

CPU

FAN

DIMM

PCIC

HDD

CPCB

XDI

XAI

GSWB

MMB

OPL

FAN TRAY

KVM

PSU

IOU

CPU

FAN

DIMM

BMM

PCIC

HDD

PCI_Box

PCIU

PCI-Slot

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands

Fujitsu PRIMEQUEST 440, System Design Manual

Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands