manualshive.com logo in svg

Fujitsu PRIMEQUEST 440, System Design Manual

Share
Download
Fujitsu PRIMEQUEST 440 System Design Manual Download Page 179

C122-B001-02EN

6-1

 

CHAPTER 6  Redundant Configuration

1

Redundant configuration refers to a configuration where even if some components 
making up the hardware configuration fail, the remaining components maintain 
adequate throughput.

PRIMEQUEST provides redundant configuration for most elements of the hardware 
configuration, such as memory, CPUs, IO_Units, chip sets, transmission lines, and 
power units, to achieve high reliability and high availability.

This chapter describes the following types of redundant configuration adopted by 
PRIMEQUEST to improve reliability and availability.

- Redundancy of Components
- Redundancy of Private LAN and Management LAN
- System Mirror
- Redundancy of an HDD (Use of PRIMECLUSTER GDS)
- Redundancy of the Business LAN (Use of PRIMECLUSTER GLS)

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands