Fujitsu PRIMEQUEST 440 System Design Manual Download

Page: 102 / 280

3-4

C122-B001-02EN

CHAPTER 3 General Software Configuration

3.2.1

Linux

Linux supports large-scale enterprise environments that require high reliability:

(1) Support of large-scale systems

Linux supports construction of large-scale systems by increasing scalability with the
following functions:

• 64-bit virtual space

Large-scale business applications can be developed without consideration of the
virtual space size.

• Support of large-scale SMP

A high-performance system with a large-scale SMP configuration can be constructed
using high-speed interconnect technology.

• Increased number of connected devices

Large-scale storage systems can be managed.

• Support of large-capacity storage

Systems that handle large-volume data can be managed.

(2) Higher reliability and availability

Linux works together with hardware to increase reliability and availability as follows:

• Enhancing drivers

Error handling is enhanced, thereby increasing reliability.

• Machine Check Abort (MCA) information logging function

Information on recoverable errors is always collected in a log and used for protection
against the errors and maintenance.

• PCI hot plugging

PCI cards that support PCI hot plugging are hot-swappable.

• Guaranteed uniqueness of device names

Each device name is guaranteed to be unique even if a device is removed or replaced
because of a disk failure.

Summary of Contents for PRIMEQUEST 440

























































































































































































































































































Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands

Fujitsu PRIMEQUEST 440, System Design Manual

Search results

Summary of Contents for PRIMEQUEST 440

Reviews:

Related manuals for PRIMEQUEST 440

Brands by name

Popular brands