background image

Yes

– 14 –

Check 1

Start

(1) Pull out Power Cord Plug and disconnect connectors CN10, CN41, CN42, CN49 and 

CN50 on Main Power PCB.

(2) Connect 1 to pin 2 and 3 to pin 4 on CN4 connector.
(3) Plug in Power Cord Plug and turn on power switch.

PDP faulty.

Power supply protector operated

Power lamp : Flashing continuously in red.

(at an interval of 1 sec)

(1) Pull out Power Cord Plug and disconnect connector CN351 and CN352 on Main Power PCB.
(2) Connect 1 to pin 13 on connector CN352.
(3) Disconnect connectors on Main Power PCB. (CN10, CN41, CN42, CN49, CN50)
(4) Plug in Power Cord Plug and turn on power switch.

(1) Pull out Power Cord Plug and connect connector CN351 and CN352 to Power Supply Unit.
(2) Remove Video PCB Assy.
(3) Plug in Power Cord Plug and turn on power switch.
(4) Check state of green lamp.

∗ 

Replace PDP.

∗ 

Vs and -Vy must be adjusted.

Yes

No

Does 

lamp change to

green?

Power Supply
circuit faulty.

Replace Main
Power PCB.

∗ 

Vs and -Vy must be adjusted.

No

Is voltage 

at each connector on 

Main Power PCB normal ? 

See page 19.

Video circuit
faulty.

Replace Video
PCB Assy.

Yes

Main/Digital
circuit faulty.

Replace Main
/Digital PCB Assy.

No

Is green lamp lit

continuously?

Summary of Contents for Plasmavision PDS4229W-B













































Reviews: