Fujitsu MAT3073NC Product/Maintenance Manual Download | Manualshive

Page: 59 / 130

background image

C141-E201

4-9

c) In a system which does not use the terminating resistor power supply signal (TERMPWR) on

the SCSI bus, the requirements for +5 VDC given in Figure 4.10 must be satisfied between the
IDD and the SCSI device with the terminating resistor circuit.

Figure 4.10 Power on/off sequence (2)

d) Between the IDD and other SCSI devices on the SCSI bus, the +5 VDC power on/off sequence

is as follows:

•

In a system with its all SCSI devices designed to prevent noise from leaking to the SCSI
bus when power is turned on or off, the power sequence does not matter if the
requirement in b) or c) is satisfied.

•

In a system containing an SCSI device which is not designed to prevent noise from
leaking to the SCSI bus, the requirement given in Figure 4.11 must be satisfied between
that SCSI device and the IDD.

Figure 4.11 Power on/off sequence (3)

SCSI devices
without noise
leaking designed

SCSI devices with
the terminating
resistor

«
...
57
58
59
60
61
...
»

Summary of Contents for MAT3073NC



































































































































Reviews:

No comments

Related manuals for MAT3073NC

Camedia MAUSB-100

Brand: Olympus Pages: 2

Brand: U-Line Pages: 6

Brand: Xigmatek Pages: 2

Brand: Forest garden Pages: 4

Brand: Tiger Pages: 16

Brand: Dahua Pages: 246

Brand: Metro DataVac Pages: 16

Brand: ABSCO SHEDS Pages: 21

Brand: NEC Pages: 4

Brand: NEC Pages: 8

Brand: NEC Pages: 12

Brand: NEC Pages: 48

Brand: NEC Pages: 53

Brand: NEC Pages: 106

Brand: NEC Pages: 118

Brand: NEC Pages: 120

Brand: NEC Pages: 168

Brand: QNAP Pages: 203

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands