manualshive.com logo in svg

Fujitsu Lifebook C2310, User Manual, Page: 78 / 116

Share
Download
Fujitsu Lifebook C2310 User Manual Download Page 78

72

L i f e B o o k   C   S e r i e s   N o t e b o o k   –   S e c t i o n   S i x

Keyboard or Mouse Problems

The built-in keyboard 
does not seem to work.

The LifeBook notebook has gone 
into Suspend mode.

Push the 

Power/Suspend/Resume

 button.

Your application has locked out 
your keyboard.

Try to use your integrated pointing device to restart 
your system. If this fails, turn your LifeBook note-
book off press the Power/Suspend/Resume button 
for 10 seconds or more, and then turn it back on.

You have installed an 
external keyboard or 
mouse, and it does not 
seem to work.

Your external device is not 
properly installed.

Re-install your device. (See Device Ports on page 46 
for more information)

Your operating system software is 
not set up with the correct 
software driver for that device.

Check your device and operating system docu-
mentation and activate the proper driver.

You have connected an 
external keyboard or a 
mouse and it seems to be 
locking up the system.

Your operating system software is 
not set up with the correct 
software driver for that device.

Check your device and operating system
documentation and activate the proper driver.

Your system has crashed.

Try to restart your LifeBook notebook. If this fails, 
turn your LifeBook notebook off press the Power/
Suspend/Resume button for 10 seconds or more, 
and then turn it back on.

Memory Problems

Your Info menu of the 
BIOS setup utility infor-
mation, does not show 
the correct amount of 
installed memory.

Your memory upgrade module is 
not properly installed.

Remove and re-install your memory upgrade 
module. (See Memory Upgrade Module on page 43 
for more information)

You have a memory failure.

Check for Power On Self Test (POST) messages. 
(See Power On Self Test Messages on page 78 for more 
information)

Modem Problems

Messages about modem 
operation.

Messages about modem 
operation are generated by 
whichever modem application is 
in use.

See your application software documentation for 
additional information.

USB, Parallel, or IR Device Problems

You have installed a 
USB, parallel, or IR 
device. Your LifeBook 
notebook does not 
recognize the device, or 
the device does not seem 
to work properly.

The device is not properly 
installed.

Remove and re-install the device. (See Device Ports 
on page 46 for more information)

The device may have been 
installed while an application was 
running, so your LifeBook is not 
aware of its installation.

Close the application and restart your LifeBook 
notebook.

Your software may not have the 
correct software driver active.

See your software documentation and activate the 
correct driver.

Problem

Possible Cause

Possible Solutions

C2310.book  Page 72  Friday, April 2, 2004  3:57 PM

Summary of Contents for Lifebook C2310





















































































































Reviews:

No comments