Fujitsu fi-7300NX Operator'S Manual Download

Page: 269 / 321

Messages for Cleaning or Replacing Consumables

The following message may appear on the computer while the scanner is in use.

Example: Message for replacing consumables

Example: Message for cleaning

Check the message, and replace the consumable or perform cleaning accordingly.

Note that, when this message appears, the touch screen displays a notification on

for a message related

to replacing the consumables or cleaning the scanner.
For details about replacing consumables, refer to the following:

●

Brake roller

Replacing the Brake Roller (page 129)

●

Pick roller

Replacing the Pick Roller (page 134)

For details about cleaning, refer to

Daily Care (page 114)

Scanner Settings (Software Operation Panel)

269

Summary of Contents for fi-7300NX


































































































































































































































































































































Search results

Summary of Contents for fi-7300NX

Reviews:

Related manuals for fi-7300NX

Brands by name

Popular brands

Fujitsu fi-7300NX, Operator'S Manual

Search results

Summary of Contents for fi-7300NX

Reviews:

Related manuals for fi-7300NX

Brands by name

Popular brands