Fujitsu fi-7300NX Operator'S Manual Download

Page: 129 / 321

Replacing the Brake Roller

Replace the brake roller in following procedure.

Turn off the scanner, unplug the power cable and wait for at least 15 minutes.
For details, refer to

How to Turn the Power OFF (page 57)

Remove all documents from the ADF paper chute (feeder).

Open the ADF.
For details, refer to

How to Open the ADF (page 63)

CAUTION

When the ADF is open, it might close accidentally. Be careful not to get your fingers
caught.

Remove the brake roller.

Hold both ends of the cover, and open it in the direction of the arrow.

Replacing the Consumables

129

Summary of Contents for fi-7300NX


































































































































































































































































































































Search results

Summary of Contents for fi-7300NX

Reviews:

Related manuals for fi-7300NX

Brands by name

Popular brands

Fujitsu fi-7300NX, Operator'S Manual

Search results

Summary of Contents for fi-7300NX

Reviews:

Related manuals for fi-7300NX

Brands by name

Popular brands