Fujitsu fi-7300NX Operator'S Manual Download Page 22 | Manualshive

Page: 22 / 321

background image

Parts and Functions

This section shows the names of the scanner parts.

●

Front

No.

Name

Function

1

Contactless Smart Card Reader

Reads the information of the smart card.

2

ADF (Automatic Document Feeder)

Pulls and feeds the documents one sheet at a time from
the ADF paper chute (feeder).
Open this to replace consumables or to clean the inside of
the scanner.

3

Chute extension

Pull out to adjust to the document length.

4

ADF paper chute (feeder)

Holds the documents to be scanned.

5

Side guide

Positions the documents in place when the documents are
loaded in the ADF paper chute (feeder) as they are fed into
the scanner.

6

Feed mode switch

Slide the feed mode switch to the left to switch the feed
mode to Manual Single Mode.

Scanner Overview

22

«
...
20
21
22
23
24
...
»

Summary of Contents for fi-7300NX


































































































































































































































































































































Reviews:

No comments

Related manuals for fi-7300NX

Brand: ClearClick Pages: 20

Brand: Colortrac Pages: 90

Brand: PASCO Pages: 5

Brand: Apperson Pages: 16

Brand: TEKNIHALL Pages: 46

SIMRAD StructureScan 3D

Brand: Lowrance Pages: 2

Brand: Vicon Pages: 7

Brand: X-Rite Pages: 2

PANTONE exact Auto-Scan

Brand: X-Rite Pages: 24

Brand: X-Rite Pages: 31

Brand: Zebex Pages: 2

Brand: Radio Shack Pages: 56

Brand: Lyngsoe Systems Pages: 34

Brand: UMAX Technologies Pages: 30

Brand: Panasonic Pages: 44

Brand: Omega Engineering Pages: 31

Brand: Twilight Pages: 41

Brand: Microtek Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands