Fujitsu fi-7300NX Operator'S Manual Download Page 152 | Manualshive

Page: 152 / 321

background image

Overrun Error

Background Switching Mechanism Error

When a background switching mechanism error occurs, the [Error] screen on the touch screen displays one of
the following codes.

F4:C2 Background switching mechanism error (ADF Front)

If the problem persists after turning the power back on, please inform your service provider of the error
code below.
Code F4:C2

F4:C3 Background switching mechanism error (ADF Back)

If the problem persists after turning the power back on, please inform your service provider of the error
code below.
Code F4:C3

Open the ADF to check that there are no documents remaining, and then turn the scanner off then back on.
If the problem persists, write down the error code and contact the distributor/dealer where you purchased this
product. Refer to the contact information in the Contact List if supplied with this product, or refer to the contact
information in the Contact for Inquiries section if provided in Safety Precautions supplied with this product, and
then make an inquiry.

Troubleshooting

152

«
...
150
151
152
153
154
...
»

Summary of Contents for fi-7300NX


































































































































































































































































































































Reviews:

No comments

Related manuals for fi-7300NX

Brand: Microtek Pages: 10

SelfServ 90 R1.2

Brand: NCR Pages: 18

Brand: UBKEY Pages: 23

8738056 - Scan Station 500

Brand: Kodak Pages: 43

Brand: Motorola Pages: 16

Symbol STB20 Series

Brand: Motorola Pages: 24

Brand: Motorola Pages: 86

Brand: Motorola Pages: 276

Symbol MiniScan MS1207FZY

Brand: Motorola Pages: 368

Brand: PPI Pages: 26

Brand: Snap-On Pages: 10

GFC-2 00 Series

Brand: Datalogic Pages: 2

Brand: MobileDemand Pages: 5

Combo-Scanner PS970

Brand: Jay-tech Pages: 32

Brand: Sense Pages: 11

XTRAVEL-SCAN - Travel Scanner 100

Brand: Xerox Pages: 12

HQPower AERON 250 II

Brand: Velleman Pages: 33

Brand: Canon Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands