Fujitsu DL7400 Page 5 Installation Manual Download | Manualshive

Page: 5 / 46

background image

Installation guide for Fujitsu Dot Matrix Printer_1.6

Page 5

Installing procedures for Fujitsu Engineer:

Fujitsu DL7400 Dot Matrix Printer will be used as an example in this section.

Unpacking the printer

1.

Open the carton box and remove the printer and its components, please handle with care.

Make sure that you have all of the items shown below. DO NOT use the power cord inside the

package and use the power cord prepared by the engineer.

2.

Carefully examine each item for damage. Report any problem is found.

«
...
3
4
5
6
7
...
»

Summary of Contents for DL7400















































Reviews:

No comments

Related manuals for DL7400

Brand: Oki Pages: 6

Brand: Oki Pages: 44

Brand: Oki Pages: 13

Brand: Oki Pages: 20

Brand: Oki Pages: 2

Brand: Oki Pages: 28

Magicolor 2 plus

Brand: QMS Pages: 90

Magicolor 2 Desklaser

Brand: QMS Pages: 4

Brand: QMS Pages: 8

Brand: QMS Pages: 94

Brand: QMS Pages: 6

imageRUNNER ADVANCE DX 6870i

Brand: Canon Pages: 115

imagerunner advance C5550i

Brand: Canon Pages: 1556

Brand: Axis Pages: 10

Brand: Printek Pages: 34

Brand: Oki Pages: 204

Brand: Lexmark Pages: 10

Suprasetter 106

Brand: HEIDELBERG Pages: 91

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands