Fujitsu BS2000 SE Series Basic Operating Manual Download Page 57

Page: 57 / 93

Optical drive activity indicator

Open/close optical drive

ID card (green); further left, above HDD module

The DVD-RW drive is used by Customer Support to install and update the M2000 software.

Use of the USB interfaces is reserved for Customer Support.

You can pull the ID card out and push it in again as far as it will go. The ID card contains various system

information, e.g. product name, serial number, MAC addresses and DNS name.

Indicators on the front panel of MU M3

Figure 18: Indicators and control elements on the front panel of MU M3

Pos.

Label

Key /

Display

Function

Status

RESET

Reset key

System restart (for Customer Support only)

NMI

NMI key

For Customer Support only

ID button /

indicator

Identifies the ID display on the front panel and at the I/O panel for

an easier server identification.

blue on

CSS

display

Notify Customer Support if on or flashing

off / orange /

orange

flashing

Global

error

display

Notify Customer Support if on or flashing

off / orange /

orange

flashing

HDD/SSD

activity

indicator

Data access running

green flashing

On/Off

button

Switch on server: Off / Server switched on / BMC firmware starting

after connection to power grid

off / green on

/ green

Summary of Contents for BS2000 SE Series






























































































Search results

Summary of Contents for BS2000 SE Series

Reviews:

Related manuals for BS2000 SE Series

Brands by name

Popular brands

Fujitsu BS2000 SE Series, Basic Operating Manual

Search results

Summary of Contents for BS2000 SE Series

Reviews:

Related manuals for BS2000 SE Series

Brands by name

Popular brands