background image

En-8

6.3.3. Remote controller cable 

Remote controller cable modi

fi

 cation.

(1) Use a tool to cut off the terminal on the end of the remote controller cable, and then 

remove the insulation from the cut end of the cable.

13/16 in (20 mm)

13/16 in (20 mm)

For 3-wire type

For 2-wire type

(2) Connect the remote controller cable with connecting cable with solder.

IMPORTANT:

   Be sure to insulate the connection between the cables.

For dual control or group control

For 3-wire type

Solder and insulate the connected parts.

Red

Red

White

Black

Remote controller cable

Connecting cable 

(Accessories)

Black

White

For 2-wire type

Solder and insulate the connected parts.

Red

Connecting cable 

(Accessories)

Remote controller 

cable (non polar)

Cut and insulate

Black

White

(3) Connect the cable of wired remote controller unit to the connector of control unit, and 

set the DIP switch (SW1).

 CAUTION

When switching the DIP switch (SW1), be sure to turn off the power supply to the 
indoor unit. Otherwise, the PC board of the indoor unit may be damaged.

For 2-wire type

For 3-wire type

Set the DIP switch (SW1)

2WIRE (Factory setting)

3WIRE

DIP switch 
(SW1)

Connector

Connecting cable 
(Accessories)

Wired remote 
controller cables

 WARNING

When using solid core cables, do not use the attached ring terminal. If you use the solid 
core cables with the ring terminal, the ring terminal's pressure bonding may malfunction 
and cause the cables to abnormally heat up.

B.  For strand wiring

(1) Use ring terminals with insulating sleeves as shown in the 

fi

 gure below to connect to 

the terminal block.

(2) Securely clamp the ring terminals to the cables using an appropriate tool so that the 

cables do not come loose.

(3) Use the speci

fi

 ed cables, connect them securely, and fasten them so that there is no 

stress placed on the terminals.

(4) Use an appropriate screwdriver to tighten the terminal screws.
 

Do not use a screwdriver that is too small, otherwise, the screw heads may be dam-
aged and prevent the screws from being properly tightened.

(5) Do not tighten the terminal screws too much, otherwise, the screws may break.
(6) See the table for the terminal screw tightening torques.
(7) Please do not 

fi

 x 2 power supply cables with 1 screw.

Strip 3/8 in 
(10 mm)

Ring terminal

Sleeve

Screw with 
special washer

Screw with 
special washer

Ring terminal

Terminal block

Ring terminal

Cable

Cable

 WARNING

Use ring terminals and tighten the terminal screws to the speci

fi

 ed torques, otherwise, 

abnormal overheating may be produced and possibly cause heavy damage inside the 
unit.

Terminal number

Tightening torque

M4 screw (Power supply/Change: L1, L2 (N), GND)

11 to 16 Ibf·in (1.2 to 1.8 N·m)

6.3.2. Transmission cable 

1-3/16 in (30 mm)

1-3/8 in (35 mm)

Shielded cable 
(no 

fi

 lm)

•  When the 2 cables are attached.

GOOD

PROHIBITED

Different diameter

Connect to 1 side

 WARNING

Tighten the terminal screws to the speci

fi

 ed torques, otherwise, abnormal overheating 

may be produced and possibly cause heavy damage inside the unit.

Terminal number

Tightening torque

M3 screw (Transmission/X1, X2)

4.4 to 5.3 Ibf·in (0.5 to 0.6 N·m)

 

CAUTION

To peel the 

fi

 lm from the lead cable, use a dedicated tool that will not damage the 

conductor cable.

When installing a screw on the terminal block, do not cut the cable by overtightening 
the screw. On the other hand, an undertightened screw can cause faulty contact, which 
will lead to a communication failure.

Remove it with the following sequence in case of the state with the grille.

9373370444_IM.indb   8

9373370444_IM.indb   8

29/11/2017   AM 11:48:43

29/11/2017   AM 11:48:43

Summary of Contents for Airstage ASUB18TLAV1


















Reviews: