Fujitsu Siemens Computers D1944 Technical Manual Download

Page: 36 / 38

Error messages

A26361-D1944-Z120-1-7419, edition 1

English - 25

Parity Check 1

Parity Check 2

Switch the device off and on again. If the message is still displayed, please contact your sales
outlet or customer service centre.

Previous boot incomplete - Default configuration used

By pressing function key

you can check and correct the settings in

BIOS Setup

. By pressing

function key

the system starts with incomplete system configuration. If the message is still

displayed, please contact your sales outlet or customer service centre.

Real time clock error

Call the

BIOS Setup

and enter the correct time in the

Main

menu. If the message is still

displayed, please contact your sales outlet or customer service centre.

Service Processor not properly installed

The server management controller has not been correctly installed. If the message is still
displayed, please contact your sales outlet or customer service centre.

System battery is dead - Replace and run SETUP

Replace the lithium battery on the mainboard and redo the settings in the

BIOS Setup

System Cache Error - Cache disabled

Switch the device off and on again. If the message is still displayed, please contact your sales
outlet or customer service centre.

System CMOS checksum bad - - Default configuration used

Call the

BIOS Setup

and correct the previously made entries or set the default entries.

System Management Configuration changed or Problem occurred

A system fan or system sensor has failed. Check the hardware operation.

System timer error

Switch the device off and on again. If the message is still displayed, please contact your sales
outlet or customer service centre.

Uncorrectable ECC DRAM error

DRAM Parity error

Unknown PCI error

Switch the device off and on again. If the message is still displayed, please contact your sales
outlet or customer service centre.

Verify CPU frequency selection in Setup

The frequency setting for the processor is invalid. Correct the

BIOS Setup

and the setting.

Summary of Contents for D1944







































Search results

Summary of Contents for D1944

Reviews:

Related manuals for D1944

Brands by name

Popular brands

Fujitsu Siemens Computers D1944, Technical Manual

Search results

Summary of Contents for D1944

Reviews:

Related manuals for D1944

Brands by name

Popular brands