FujiFilm FinePix REAL 3D W1, Owner'S Manual

Page: 2 / 128

ii
For Your Safety
IMPORTANT SAFETY INSTRUCTIONS
• Read Instructions : All the safety and op-
erating instructions should be read
before the appliance is operated
.
• Retain Instructions : The safety and
operating instructions should be
retained for future reference.
• Heed Warnings : All warnings on the
appliance and in the operating in-
structions should be adhered to.
• Follow Instructions : All operating and
use instructions should be followed.
Installation Installation
Power Sources : This video product
should be operated only from the
type of power source indicated on
the marking label. If you are not sure
of the type of power supply to your
home, consult your appliance dealer
or local power company. For video
products intended to operate from
battery power, or other sources, refer
to the operating instructions.
Grounding or Polarization : This video
product is equipped with a polar-
ized alternating-current line plug (a
plug having one blade wider than
the other). This plug will fi t into the
power outlet only one way. This is a
safety feature. If you are unable to
insert the plug fully into the outlet,
try reversing the plug. If the plug
should still fail to fi t, contact your
electrician to replace your obsolete
outlet. Do not defeat the safety pur-
pose of the polarized plug.
Alternate Warnings : This video prod-
uct is equipped with a three-wire
grounding-type plug, a plug having
a third (grounding) pin. This plug
will only fi t into a grounding-type
power outlet. This is a safety feature.
If you are unable to insert the plug
into the outlet, contact your electri-
cian to replace your obsolete outlet.
Do not defeat the safety purpose of
the grounding type plug.
Overloading : Do not overload wall out-
lets and extension cords as this can
result in a risk of fi re or electric shock.
Ventilation : Slots and openings in
the cabinet are provided for ventila-
tion, to ensure reliable operation of
the video product and to protect it
from overheating, and these open-
ings must not be blocked or cov-
ered. The openings should never
be blocked by placing the video
product on a bed, sofa, rug, or other
similar surface.
This video product should not be
placed in a built-in installation such
as a bookcase or rack unless proper
ventilation is provided or the manu-
facturer’s instructions have been ad-
hered to. This video product should
never be placed near or over a radia-
tor or heat register.
Attachments : Do not use attachments
not recommended by the video
product manufacturer as they may
cause hazards.
Water and Moisture : Do not use this
video product near water—for ex-
ample, near a bath tub, wash bowl,
kitchen sink, or laundry tub, in a wet
basement, or near a swimming pool,
and the like.
Power-Cord Protection : Power-sup-
ply cords should be routed so that
they are not likely to be walked on
or pinched by items placed upon
or against them, paying particular
attention to cords at plugs, conve-
nience receptacles, and the point
where they exit from the appliance.
Accessories : Do not place this video
product on an unstable cart, stand,
tripod, bracket, or table. The video
product may fall, causing serious in-
jury to a child or adult, and serious
damage to the appliance. Use only
with a cart, stand, tripod, bracket, or
table recommended by the manufac-
turer, or sold with the video product.
Any mounting of the appliance should
follow the manufacturer’s instructions,
and should use a mounting accessory
recommended by the manufacturer.
An appliance and
cart combination
should be moved
with care. Quick
stops, excessive
force, and uneven
surfaces may
cause the appliance and cart combi-
nation to overturn.
Antennas Antennas
Outdoor Antenna Grounding : If an
outside antenna or cable system is
connected to the video product, be
sure the antenna or cable system is
grounded so as to provide some pro-
tection against voltage surges and
built-up static charges. Section 810
of the National Electrical Code, ANSI/
NFPA No. 70, provides information
with respect to proper grounding
of the mast and supporting struc-
ture, grounding of the lead-in wire
to an antenna discharge unit, size of
grounding conductors, location of
antenna discharge unit, connection
to grounding electrodes, and require-
ments for the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS
PER NATIONAL ELECTRICAL CODE
Antenna Lead
in Wire Ground
Clamp
Electric
Service
Equipment
Ground
Clamps
Grounding
Conductors
(NEC SECTION
810-21)
Power Service Grounding
Electrode System (NEC
ART 250. PART H)
Antenna
Discharge
Unit (NEC
SECTION
810-20)
Power Lines : An outside antenna sys-
tem should not be located in the
vicinity of overhead power lines or
other electric light or power circuits,