FujiFilm FINEPIX A203, Owner'S Manual

Page: 38 / 67

75
6
Software needed for playing back movies, etc.
Launches the FinePixViewer
software when a camera is
connected.
Software used to read PDF-format documents on a
personal computer. This software is needed to read the
User’s Guides for FinePixViewer.
Creates a FinePix CD Album.
Used for videoconferencing (Windows only).
Allows you to display thumbnail lists of the
images stored on your PC or in the camera,
print the images individually or as an index,
display the images at full size and perform
some basic image processing.
✽
Note that the software configuration differs slightly depending on your operating system.
Connect the camera
with “DSC” selected as
the USB setting
(
➡
P.88).
Connect the camera
with “PC CAM”
selected as the USB
setting (
➡
P.91).
Allows a digital camera to be used
as USB Mass Storage (removable
disk drive, card reader).
Allows a digital camera to be
used as a PC Camera.
ImageMixer VCD
for FinePix
FinePixViewer
PictureHello
Acrobat Reader R
QuickTime
USB PC Camera
Driver
Exif Launcher
USB Mass Storage
Driver
6 Software Installation
6.1 The Software Components
74
ＤＡＴＥ／ＴＩＭＥ ＤＡＴＥ／ＴＩＭＥ
ＵＳＢ ＭＯＤＥ
ＰＯＷＥＲ ＳＡＶＥ ＯＮ ＯＮ
ＰＯＳＴＶＩＥＷ ＰＯＳＴＶＩＥＷ ＯＮ ＯＮ
ＳＥＴ ＳＥＴ
ＤＳＣ ＤＳＣ ＤＳＣ ＤＳＣ ＤＳＣ
ＳＥＴ−ＵＰ ＳＥＴ−ＵＰ
ＢＡＣＫ ＢＡＣＫ ＢＡＣＫ ＯＫ ＯＫ ＯＫ
h
Power saving “ON” (default setting)
Power consumption is kept to a minimum to
prevent battery depletion. You should select the
“ON” setting when you are using alkaline
batteries.
i If the camera is not used for approximately 30
seconds, the LCD monitor switches off temporarily
to reduce power consumption (Sleep mode).
i Once the camera is in Sleep mode, if it is left
unused for a further 90 seconds, it is automatically
switched off.
i The charging time for the flash increases slightly
because the flash charging power is reduced.
h Power saving “OFF”
Batteries are more likely to run flat since no
power reduction measures (sleep mode, etc.)
are used. However, this function automatically
switches the camera off if the camera is not
used for approximately 2 minutes.
g
POWER SAVE
SET–UP
When the camera is in Sleep mode, pressing
any button on the camera will switch the LCD
monitor back on. You can take a picture even
while the LCD monitor is switched off simply by
pressing the shutter button.
●
!
If you press the shutter button down halfway and
then release it, the screen may go dark briefly
because the flash is charging.
●
!
The Power Save and Auto Power Off functions are
disabled during USB connection.
The Sleep function does not operate when
the LCD monitor is switched off, during
setup, or in Playback mode, but the camera
still switches off automatically if it is not used
for 2 minutes.