Home
/
Fuji Xerox
/
DocuPrint C5155d
/
User Manual

Fuji Xerox DocuPrint C5155d, User Manual

Share

Page: 203 / 433

Fuji Xerox DocuPrint C5155d User Manual Download Page 203

6.1 Clearing Paper Jams

203

6

Troubleshooting

If you encounter a problem while using this printer and have trouble solving it, see if any of the
symptoms in the following pages "6.1 Clearing Paper Jams" (P. 203) through "6.8 Network-
related Problems" (P. 275) match your problem.

If your problem is described in the following pages, apply the suggested solution provided for the
problem.

If your problem is not described, or could not be solved with the suggested solution, contact our
Customer Support Center or your dealer.

6.1

Clearing Paper Jams

A paper jam will disable the machine and cause an alarm to sound. An <Error> lamp will light on
the control panel and an error message will appear on the display. Use the figure on the bottom
left of the control panel to check the location of the paper jam described in the message, and
remove the jammed paper.
After the paper jam is cleared, printing restarts automatically from the point where printing
stopped due to the paper jam.

Alpha-

numerics

indicated in

the figure

Position of Paper Jams

on the Message

Paper Jam Solution

Reference

Pages

1, 2, 3 & 4

Tray 1 to 4

Paper Jam in Trays 1 - to 4

5

Tray 5 (Bypass tray)

Paper Jam in the Bypass Tray 5

A

Cover A

Paper Jams in Upper Left Cover A

B

Cover B

Paper Jams in Duplex Module Cover B

C

Cover C

Paper Jams in Bottom Left Cover C

D

Cover D

Paper Jams in Top Left Cover D

-

High Capacity Feeder / Tray
6

Paper Jams in Tray 6 (HCF B1)

-

Finisher / Top cover

Paper jams under the Finisher Top Cover

F

Finisher / Transport Cover F

Paper Jams in the Finisher Transport Cover F

-

Finisher / Exit Cover H

Paper Jams at H in the Finisher

-

Finisher / [2a]

Paper Jams at 2a in the Finisher

-

Finisher / [2b]

Paper Jams at 2b in the Finisher

-

Finisher / [3]

Paper Jams at 3 in the Finisher

-

Finisher / [4] / [4a]

Paper Jams at 4a in the Finisher

-

Finisher / [4] / [4b]

Paper Jams at 4b in the Finisher

-

Finisher / [4a] / [Right
Bottom Tray]

Paper Jams in the Right bottom tray

«
...
201
202
203
204
205
...
»

Summary of Contents for DocuPrint C5155d


















































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands