77
INZ-TN2ZPB-E
(Option)
2. Standard Functions
Output signal holding:
Output signals are held unchanged during
manual and auto calibrations by activation
of holding (turning “ON” its setting).
The values held are those just before
start calibration mode or setting value.
Usage is selectable.
Indication of instantaneous values will
not be held.
Switch ranges:
The switch ranges function is available in
manual, auto, and remote modes. Only
preset switch method is effective.
0DQXDO
$OORZVUDQJHWRVZLWFKE\NH\RSHUDWLRQ
$XWR
$XWRPDWLFDOO\VZLWFKHGIURP¿UVWUDQJHWR
second range when the measured value
H[FHHGV)6RI¿UVWUDQJH
$XWRPDWLFDOO\VZLWFKHGIURPVHFRQGUDQJH
WR¿UVWUDQJHZKHQWKHPHDVXUHGYDOXH
GURSVWRRUOHVV¿UVWUDQJH
5HPRWH 9ROWDJHFRQWDFWLQSXW
$OORZV UDQJH WR VZLWFK YLD DQ H[WHUQDO
signal when remote range switch input
is received.
When the contact input terminals for
each component are input voltage, the
¿UVWUDQJHLVVHOHFWHGDQGLWLVVZLWFKHG
to the second range when the terminals
are open.
* These switch range value are settable between
WKH¿UVWUDQJHDQGVHFRQGUDQJHYDOXHVORZKLJK
range values).
3. Optional Functions
Remote output holding:
Output signal is held at the last value
or preset value by voltage input to the
remote output holding input terminals.
Holding is maintained while is voltage
input to the terminals. Indication of in-
stantaneous values are not held.
5DQJHLGHQWL¿FDWLRQVLJQDO
7KHSUHVHQWPHDVXULQJUDQJHLVLGHQWL¿HG
by a contact position.
The contact output terminals close for
HDFK FRPSRQHQW ZKHQ WKH ¿UVW UDQJH
is selected, and open when the second
range is selected.
Auto calibration:
$XWRFDOLEUDWLRQLVFDUULHGRXWSHULRGLFDOO\
at the preset cycle.
When a standard gas cylinder for calibra-
tion and a solenoid valve for opening/
FORVLQJWKHJDVÀRZOLQHDUHSUHSDUHGH[
-
ternally by the customer, calibration will be
carried out with the solenoid valve drive
contacts for zero calibration and each
span calibration turned on/off sequentially
at the set auto calibration timing.
$XWRFDOLEUDWLRQF\FOHVHWWLQJ
$XWRFDOLEUDWLRQF\FOHLVVHW
Setting is variable within 1 to 99 hours
(in increments of 1 hour) or 1 to 40 days
(in increments of 1 day).
*DVÀRZWLPHVHWWLQJ
7KHWLPHIRUÀRZLQJHDFKFDOLEUDWLRQJDV
in auto calibration is set.
Settable within 60 to 900 seconds (in
increments of 1 second)
Auto calibration remote start:
$XWR FDOLEUDWLRQ VWDUWV E\ RSHQLQJ WKH
auto calibration remote start input terminal
after short circuiting for 1.5 sec or longer.
$XWR FDOLEUDWLRQ VWDUWV ZKHQ FRQWDFWV
open.
Auto zero calibration:
$XWR]HURFDOLEUDWLRQLVFDUULHGRXWSHUL
-
odically at the preset cycle.
7KLV F\FOH LV LQGHSHQGHQW IURP ³$XWR
calibration” cycle.
When zero calibration gas and solenoid
valve for opening/closing the calibration
JDVÀRZOLQHDUHSUHSDUHGH[WHUQDOO\E\
the customer, zero calibration will be car-
ried out at the set auto zero calibration
timing.
$XWR]HURFDOLEUDWLRQF\FOHVHWWLQJ
$XWR]HURFDOLEUDWLRQF\FOHLVVHW
Setting is variable within 1 to 99 hours
(in increments of 1 hour) or 1 to 40 days
(in increments of 1 day)
*DVÀRZWLPHVHWWLQJ
7KH WLPLQJ IRU ÀRZLQJ ]HUR JDV LQ DXWR
zero calibration is set.
Settable within 60 to 900 seconds (in
increments of 1 second)
High/low limit alarm:
$ODUP FRQWDFW RXWSXW WXUQV RQ ZKHQ
measurement value reaches the preset
high or low limit alarm value.
Contacts close when the instantaneous
value of each channel exceeds the high
alarm limit value or falls below the low
alarm limit value.
Instrument error contact output:
Contacts turn on at occurrence of analyzer
error No. 1, 2, 3 or 10.
Calibration error contact output:
Contacts turn on at occurrence of manual
or auto calibration error (any of errors No.
4 to 9).
Auto calibration status contact outputs:
Contacts turn on during auto calibration.
O
2
correction:
Correction of measured NO, SO
2
and
CO gas concentrations into values at
reference O
2
concentration.
