29
INZ-TN2ZPAH-E
6.2.4 Setting of auto calibration component/range
6HOHFWWKH&KFRPSRQHQWDQGWKHUDQJHIRUZKLFKDXWRFDOLEUDWLRQLVWREHSHUIRUPHG7KH&KIRU
ZKLFK³$5´KDVEHHQVHOHFWHGDVUDQJHVZLWFKPRGHLVFDOLEUDWHGLQWKHUDQJHVHWKHUH$XWRFDOL
-
EUDWLRQDQGWKHPDQXDOFDOLEUDWLRQRIWKHFRPSRQHQWIRUZKLFK³$5´KDVEHHQVHOHFWHGDVUDQJH
VZLWFKPRGHDUHSHUIRUPHGLQWKHUDQJHVHOHFWHGKHUH
6HOHFW8VHUPRGH!
o
&DOLEUDWLRQ
SDUDPHWHUV!
o
$XWRFDOLEUDWLRQFRP
-
SRQHQWUDQJH!³$XWR&DOLEUDWLRQ&RP
-
SRQHQW5DQJH´VHWWLQJVFUHHQDSSHDUVDV
VKRZQDWULJKW
6HOHFWWKH&K\RXZDQWWRFKDQJHE\
SUHVVLQJWKH RUWKH NH\3UHVVWKH
ENT
NH\DQGWKHVHOHFWHGFXUVRULVKLJK
-
OLJKWHG
6HOHFWWKHUDQJHWREHFDOLEUDWHGPDLQO\
E\SUHVVLQJWKH RUWKH
key.
7KHQSUHVVWKH
ENT
NH\DQGFDOLEUDWLRQ
LVSHUIRUPHGLQWKHVHOHFWHGUDQJHZKHQ
DXWRFDOLEUDWLRQRUDXWR]HURFDOLEUDWLRQLV
performed.
Auto calibration and the manual calibration
of the component for which “AR” has been
selected as range switch mode are performed
in the range selected here. In this case, once
the calibration is started, the range is
automatically switched, and on completion
of the calibration, the original range is
resumed.
The range identification contact is inter-
locked with the range after the switch.
However, if the hold setting is set to “ON,”
the contact status before calibration is main-
tained.
“Auto Calibration Component/range”
setting
Cal. Settings
Auto Cal.
Range1
Range2
0–10.00
vol%
0–20.00
vol%
Range1
Range2
0–500.0
ppm
0–2000
ppm
Ch1
CO
2
Ch2
CO
Set enable or disable
for auto calibration
enable
enable
( )
ENT
3UHVVWKH NH\LQWKHVWDWHGHVFULEHGLQ
DQGWKHKLJKOLJKWLVVZLWFKHGEHWZHHQ
³HQDEOH´DQG³GLVDEOH´DXWRFDOLEUDWLRQ
6HOHFW³HQDEOH´RU³GLVDEOH´E\SUHVVLQJ
WKH RUWKH
key.
7KHQSUHVVWKH
ENT
key.
Cal. Settings
Auto Cal.
Range1
Range2
0–10.00
vol%
0–20.00
vol%
Ch1
CO
2
Ch2
CO
Select a range for
auto calibration
enable
enable
Range1
Range2
0–500.0
ppm
0–2000
ppm
( )
ENT
End of Auto Calibration
Range Setting
End of Auto Calibration
component setting
