Fuji Electric OPC-G1-PG Instruction Manual Download Page 1

- 1 -

 

 

 

Instruction Manual

 

PG Interface Card "OPC-G1-PG"

 

  

 

 

 

Thank you for purchasing this PG interface card "OPC-G1-PG." Installing this card to your FRENIC-MEGA enables speed control with 
speed sensor and pulse train input. 

 

  Installing this card disables pulse train inputs to the inverter's terminal [X7]. 

  The FRENIC-MEGA has three option connection ports--A-, B-, and C-ports. Connect this PG interface card to the C-port. 

Do not connect it to any other port. 

 

1.  Check that: 

 
 

 

 

(1)  A PG interface card and two screws (M3 

×

 8) are contained 

in the package. 

(2)  The 

PG 

interface 

card 

is 

not 

damaged 

during 

transportation--no defective devices, dents or warps. 

(3)  The model name "OPC-G1-PG/SY" is printed on the back of 

the  PG  interface  card  as  shown  in  Figure  2.  (The  "PG/SY" 
on the front is a short name, as shown in Figure 1.) 

If  you  suspect  the  product  is  not  working  properly  or  if  you 
have  any  questions  about  your  product,  contact  the  shop 
where you bought the product or your local Fuji branch office.

 

Figure 1    Front of Card 

Figure 2    Back of Card 

 

2.  Installation 

 

Before starting installation and wiring, turn OFF the power and wait at least five minutes for inverters with a capacity of 22 kW or 
below, or at least ten minutes for inverters with a capacity of 30 kW or above. Make sure that the LED monitor and charging lamp are 
turned OFF. Further, make sure, using a multimeter or a similar instrument, that the DC link bus voltage between the terminals P(+) 
and N(-) has dropped to the safe level (+25 VDC or below).

 

Otherwise, electric shock could occur. 

 

(1)  Remove the front cover from the inverter and expose the control printed circuit board (control PCB). As shown in Figure 3, the 

PG interface card can be connected to the C-port (CN6) only. 

  To remove the front cover, refer to the FRENIC-MEGA Instruction Manual, Section 2.3. For inverters with a capacity of 30 

kW or above, open also the keypad enclosure. 

(2)  Insert connector CN1 on the back of the PG interface card (Figure 2) into the C-port (CN6) on the inverter's control PCB. Then 

tighten the two screws that come with the card. (Figure 4) 

 

Check that the positioning cutout (Figure 1) is fitted on the tab (

 in Figure 4) and connector CN1 is fully inserted (

 in 

Figure 4). Figure 5 shows the PG interface card correctly mounted. Do not connect the PG interface card to the ports other 
than C-port. Doing so may damage the card. 

(3)  Perform wiring on the PG interface card. 

 

Refer to Section 3 "Wiring." 

(4)  Put the front cover back into place. 

  To put back the front cover, refer to the FRENIC-MEGA Instruction Manual, Section 2.3. For inverters with a capacity of 30 

kW or above, close also the keypad enclosure. 

 

 

 

  Fit the positioning cutout of the card over the 

tab on the inverter to determine the 
mounting position. 

  Insert connector CN1 on the card into the 

C-port (CN6) on the inverter's control PCB.

 

 

Figure 3    In the case of 0.4 kW 

Figure 4    Mounting PG Interface Card 

Figure 5    Mounting Completed 

 

Screw hole (left)

 

Short name

 

Screw hole (right)

 

J1 

CN1 

Model name

 

Positioning cutout

 

Release knob

 

Tab

 

 

 

Reviews: