Fuji Electric Frenic-Sce, Instruction Manual

Page: 39 / 78

5-3
Code Keypad code Name Data setting range Factory
default
Setting
U132 U132 PID gains switching (P gain 1 for fast
reaction, Feedback < Set point) 0.00 to 30.00 times 0.00 1.4
(Note 1)
U133 U133 PID gains switching (I Integral time 1 for
fast reaction, Feedback < Set point) 0.0 to 3600.0 s 0.00 0.3
(Note 1)
y20 y20 RS-485 Communication 2 (Protocol
selection) 0: Modbus RTU protocol
1: FRENIC Loader protocol (SX protocol)
2: Fuji general-purpose inverter protocol 0 App.
(Note 1)
U128 U128 Tank level detection function (High level) 0.00 to 100.0%
100%: Maximum detection level
0.00 100.0
UA14 U15 Tank level detection function (High level
hysteresis width) 0.00 to 100.0%
100%: Maximum detection level 5 5
UA18 U19 Tank level detection function (Signal ON
Delay Time) 0.00 to 60 s 15 15
UA23 U24 Tank level detection function (Signal
OFF Delay Time) 0.00 to 60 s 15 15
U130 U130 Low power detection function (Low
Power level) 0.00 to 100.0%
100%: Motor rated power (P02) 0.00 App.
(Note 1)
UA48 U49 Low power detection function (Signal ON
Delay Time) 0.00 to 60 s 15 15
UA53 U54 Dry pump detection function (Output
frequency level) 0.00 to 100.0%
100%: Maximum frequency (F03) 80 80
UA54 U55 Dry pump detection function (Output
frequency hysteresis width) 0.00 to 100.0%
100%: Maximum frequency (F03) 5 5
UA68 U69 Dry pump detection function (Motor
power level) 0.00 to 100.0%
100%: Motor rated power (P02) 30 30
UA69 U70 Dry pump detection function (Motor
power hysteresis width) 0.00 to 100.0%
100%: Motor rated power (P02) 5 5
UA73 U194 (U190=15) Dry pump detection function (Signal ON
Delay Time) 0.00 to 60 s 15 15
U124 U124 Dry pump detection function (Enable Dry
Pump Alarm) 0.00: Disable dry pump alarm (OH2)
1.00: Enable dry pump alarm (OH2) 0.00 0.00
U126 U126 PV panel specifications (PV panel open
circuit voltage) 0.00 to 1000 V 0.00 App.
(Note 1)
U127 U127 PV panel specifications (PV panel MPP
voltage) 0.00 to 1000 V 0.00 App.
(Note 1)
U172 U172 Measurement at open circuit voltage
condition (affected by multiplication
factor U127/U126) 0.00 to 100.0%
100%=500V (-2/-7), 1000V (-4) - -
U121 U121 MPP search (Enable MPP search) 0.00: Disable MPP search
1.00: Enable MPP search 0.00 1.00
U123 U123 MPP search (Enable manual setting of
PV panel voltage set point) 0.00: Disable manual setting of U171
1.00: Enable manual setting of U171 0.00 0.00
U171 U171 MPP search (Actual PV panel voltage
set point) 0.00 to 100.0%
100%=500V (-2/-7), 1000V (-4) 0.00 App.
(Note 1)
U135 U135 MPP search (Voltage/PID set point
increase/decrease step for MPP search) 0.00 to 100.0%
100%=500V (-2/-7), 1000V (-4) 0.00 0.20
UB88 U194 (U190=38) MPP search (Time interval) 0.01 to 1.00 0.02 0.02
J15 J15 Sleep function (Sleep frequency) 0.0 (Disable): 1.0 to 500.0 Hz 0.0 App.
(Note 1)
U134 U134 Sleep function (Power level to keep
Running) 0.00 to 100.0%
100%: Motor rated power (P02) 0.00 25.0
UD88 U194 (U190=78) Sleep function (Sleep time) 0.00 to 60 s (recommended range) 40 40
U131 U131 Wake up function (DC link voltage level
to start) 0.00 to 500 V: (200V class)
0.00 to 1000 V: (400V class) 0.00 250
500
UD98 U194 (U190=80) Wake up function (time) 0.00 to 180 s (recommended range) 60 60
U125 U125 Big step detection (Disable) 0.00: Enable big step
1.00: Disable big step 0.00 0.00
UI08 U194 (U190=162) Big step detection (Dead time for next
action)
0.00 to 20.0 s (recommended range) 6.00 6.00
UH18 U194 (U190=144) Big step UP detection (Level to detect
big step UP)
0.00 to 100.0%
100%=500V (-2/-7), 1000V (-4) 3 3
UH48 U194 (U190=150) Big step UP detection (Time to follow the
step UP change)
0.00 to 4.0 s (recommended range) 1.0 1.0