FSR DV-MFSW-94 User Manual Download Page 27

  27

9 Limited Warranty 

The DV-MFSW-94

 

is warranted against failures due to defective parts or faulty workmanship for a period of 

three years after delivery to the original owner. During this period, FSR will make any necessary repairs or 
replace the unit without charge for parts or labor. Shipping charges to the factory or repair station must be 
prepaid by the owner, return-shipping charges (via UPS Ground) will be paid by FSR. 
 
This warranty applies only to the original owner and is not transferable. In addition, it does not apply to 
repairs done by other than the FSR factory or Authorized Repair Stations. 
 
This warranty shall be cancelable by FSR at its sole discretion if the unit has been subjected to physical 
abuse or has been modified in any way without written authorization from FSR. FSR’s liability under this 
warranty is limited to repair or replacement of the defective unit. 
 
FSR will not be responsible for incidental or consequential damages resulting from the use or misuse of its 
products. Some states do not allow the exclusion of incidental or consequential damages, so the above 
limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other 
rights which vary from state to state. 
 
Warranty claims should be accompanied by a copy of the original purchase invoice showing the purchase 
date (if a Warranty Registration Card was mailed in at the time of purchase, this is not necessary). Before 
returning any equipment for repair, please read the important information on service below. 
 
 
SERVICE 
 
Before returning any equipment for repair, please be sure that it is adequately packed and cushioned 
against damage in shipment, and that it is insured. We suggest that you save the original packaging and 
use it to ship the product for servicing. Also, please enclose a note giving your name, address, phone 
number and a description of the problem. 
 
NOTE: all equipment being returned for repair must have a Return authorization (RMA) Number. To get a 
RMA Number, please call the FSR Service Department (1-800-332-FSR1). Please display your RMA 
Number prominently on the front of all packages. 
 
 

CONTACT INFORMATION 

 

FSR INC. 

244 Bergen Blvd. 

Woodland Park, NJ 07424 

Phone:  (973) 785-4347 

*Order Desk Fax: (973) 785-4207 

E-mail:  

[email protected]

 

Web Site: 

http://www.fsrinc.com

 

 
 
 

Summary of Contents for DV-MFSW-94




























Reviews: