background image

HEATED LANDING ZONE 

CHAPTER 1: WARRANTY INFORMATION 

 
 
 

 

1

The Frymaster Corporation makes the following limited warranties to the original purchaser only for this 
equipment and its replacement parts: 
 
 

1.1  Warranty Provisions – Heated Landing Zone (HLZ) 

 

A.  The Frymaster Corporation warrants all components against defects in material and workmanship for a period 

of 1 year. 

 
B.  All parts, with the exception of fuses, are warranted for 1 year after installation date of cabinet. 
 
C.  If any parts, except fuses, become defective during the first year after installation date, Frymaster will also pay 

straight-time labor costs to replace the part, plus up to 100 miles/160 km of travel (50 miles/80 km each way). 

 
 

1.2  Parts Return 

 
All defective in-warranty parts must be returned to a Frymaster Authorized Factory Service Center within 60 days 
for credit.  After 60 days, no credit will be allowed. 
 
 

1.3  Warranty Exclusions 

 

This warranty does not cover equipment that has been damaged due to misuse, abuse, alteration, or accident 
such as: 
 

  improper or unauthorized repair; 

  failure to follow proper installation instructions and/or scheduled maintenance procedures as prescribed in 

your MRC cards; 

 improper 

maintenance; 

  damage in shipment; 

 abnormal 

use; 

  removal, alteration, or obliteration of the rating plate; 

 
This warranty also does not cover: 
 

  transportation or travel over 100 miles/160 km (50 miles/80 km each way), or travel time over two (2) 

hours; 

  overtime or holiday charges; 

  consequential damages (the cost of repairing or replacing other property which is damaged), loss of time, 

profits, use or any other incidental damages of any kind. 

 
There are no implied warranties or merchantability or fitness for any particular use or purpose. 
 
For international warranty, the above procedures apply, except that the customer is responsible for freight and 
duty charges. 

Summary of Contents for Heated Landing Zone HLZ












Reviews: