background image

ENG

45 min

PRO UNDER RACK 

TABLE bracket 

TBRA016_REV_A00

© COPYRIGHT  2016 FRONT RUNNER VEHICLE OUTFITTERS

1

IMPORTANT WARNING!

Thank you for purchasing a Front Runner Pro Under Rack Table Bracket.

Before you start, take a moment to familiarize yourself with this Fitting Instruction and the components received. 

Refer to Page 2 for a list of all the components, quantities and tools required.

IT IS CRITICAL THAT ALL FRONT RUNNER PRODUCTS BE PROPERLY AND SECURELY ASSEMBLED AND ATTACHED TO YOUR VEHICLE. 

IMPROPER ATTACHMENT COULD  RESULT IN AN AUTOMOBILE ACCIDENT,  AND COULD CAUSE SERIOUS BODILY INJURY OR DEATH. 

YOU ARE RESPONSIBLE FOR ASSEMBLING AND SECURING ALL FRONT RUNNER PRODUCTS TO YOUR VEHICLE. CHECKING THE ATTACHMENTS PRIOR TO USE, AND PERIODICALLY INSPECTING THE PRODUCTS FOR ADJUSTMENT, WEAR AND DAMAGE. 

THEREFORE YOU MUST READ AND UNDERSTAND ALL OF THE INSTRUCTIONS AND PRECAUTIONS SUPPLIED WITH YOUR FRONT RUNNER PRODUCT PRIOR TO INSTALLATION OR USE. 

IF YOU DO NOT UNDERSTAND ALL OF THE INSTRUCTIONS AND CAUTIONS, OR IF YOU HAVE NO MECHANICAL EXPERIENCE AND ARE NOT THOROUGHLY FAMILIAR WITH THE INSTALLATION PROCEDURES, 

YOU SHOULD HAVE THE PRODUCT INSTALLED BY A PROFESSIONAL INSTALLER OR OTHER QUALIFIED PERSONNEL.

TBRA016

READ ME !

Summary of Contents for PRO UNDER RACK TABLE bracket








Reviews: