background image

Safety rules

Explanation of
safety notices

DANGER!

Indicates immediate danger.

If not avoided, death or serious injury will result.

WARNING!

Indicates a potentially hazardous situation.

If not avoided, death or serious injury may result.

CAUTION!

Indicates a situation where damage or injury could occur.

If not avoided, minor injury and/or damage to property may result.

NOTE!

Indicates a risk of flawed results and possible damage to the equipment.

General

The device has been manufactured in line with the state of the art and according
to recognized safety standards. If used incorrectly or misused, however, it can
cause:

-

Injury or death to the operator or a third party

-

Damage to the device and other material assets belonging to the operating
company.

All personnel involved in commissioning, maintenance, and servicing of the
device must:

-

Be suitably qualified

-

Have knowledge of and experience in dealing with electrical installations and

-

Have fully read and precisely followed these Operating Instructions

The Operating Instructions must always be at hand wherever the device is being
used. In addition to the Operating Instructions, attention must also be paid to
any generally applicable and local regulations regarding accident prevention and
environmental protection.

All safety and danger notices on the device:

-

Must be kept in a legible state

-

Must not be damaged

-

Must not be removed

-

Must not be covered, pasted or painted over

The terminals can reach high temperatures.

Only operate the device when all protection devices are fully functional. If the
protection devices are not fully functional, there is a danger of:

-

Injury or death to the operator or a third party

-

Damage to the device and other material assets belonging to the operating
company

7

EN

Summary of Contents for TS 5kA-3

















































Reviews: