background image

General Information 

Permitted Uses 

 

 

page 6 

a

 

B 034 00 04

 

a

 

General information 

2.1 

Permitted uses 

The boiler should only be operated when it is fully efficient. The boiler should be operated in 
accordance with the instructions given in this manual. Implement all the necessary safety 
precautions. Before you start using the boiler, make sure that you are aware of the potential 
hazards involved. Ensure that any malfunctions, which might impact safety are traced any 
removed immediately. 

The Turbomat is designed exclusively for heating domestic water. Only use the fuels 
specified below 2.1.1. 
The manufacturer or supplier are not liable for any damages resulting from non-
permitted uses. 

2.1.1 

Permitted fuel 

For Germany: 

waste-wood conforming to 1. BImSchV of 15 July 1988 

For Austria:

 waste-wood conforming to 

ÖNORM M 7133

 

 

Designation 

Description 

W20 

air dried 

W30 

requires storage 

W35 

requires limited storage 

W40 

damp 

Water content 

W50 

wet 

G30 

Fine waste-wood  (for screw feeders) 

G50 

Medium waste-wood  (for screw feeders) 

Size 

G100 

Large waste-wood  (for hydraulic feeders only) 

 

IMPORTANT 

Corrosive deposits. Do not burn non-approved fuels. Do not operate at low temperatures which 
cause condensation. Burning non-approved fuels will cause a build up of corrosive deposits. 
Condensation also corrodes. 

 

Operating under these conditions will void your guarantee. May cause 
damage or corrosion in the combustion chamber.

 

2.1.2 

Who May Operate the Boiler 

Only trained operators are permitted to operate the boiler. 

IMPORTANT 

No unauthorized access to the boiler room. 

 

 

 

Hazard: Personal injury and damage to property. 

 

 

  It is the responsibility of the operator to ensure that unauthorized persons, especially 

children, are kept away from the boiler. 

 

 

Summary of Contents for Turbomat 320
































Reviews: