Fröling T4e Operating Instructions Manual Download Page 38

Page: 38 / 76

4.4.4 Change boiler mode

Depending on the type of boiler, there are several

modes available which can be changed directly in the

basic display of the touch display.

Mode

Icon

Description

Automatic

Supply heating circuits and domestic hot water tanks

with heat according to the selected heating times.

Domestic hot water

The domestic hot water tank is supplied with heat within

the selected loading times. Heating circuits are switched

off, frost protection remains active.

Continuous load

The boiler continuously maintains the selected boiler

temperature setpoint and only shuts down for cleaning

purposes. Supply heating circuits and domestic hot

water tanks with heat according to the selected heating

times.

NOTICE! Consult the enclosed operating instructions for the boiler controller for a
detailed description of the boiler modes.

Operating the System

Operate the boiler using the touch display

Froling GesmbH | A-4710 Grieskirchen, Industriestraße 12 | www.froeling.com

Summary of Contents for T4e













































































Search results

Summary of Contents for T4e

Reviews:

Related manuals for T4e

Brands by name

Popular brands

Fröling T4e, Operating Instructions Manual

Search results

Summary of Contents for T4e

Reviews:

Related manuals for T4e

Brands by name

Popular brands