Fritz! Box 6490 cable Installation And Operation Manual Download Page 75 | Manualshive

Page: 75 / 173

background image

VPN: Remote Access to the Home Network

FRITZ!Box 6490 Cable

75

•

Discard low-priority packets in order to ensure the trans-
mission of higher-priority packets. This technique is
used whenever more packets are supposed to be sent to
the Internet than the upstream transmission rate of the
Internet connection allows.

•

As long as no packets are being sent from higher-priority
applications, the full transmission rate of the Internet
connection is available for low-priority packets.

Configuring Prioritization in the FRITZ!Box

1.

Open the FRITZ!Box user interface; see

.

2.

Enable the advanced view.

3.

Configure prioritization in the “Internet / Filters / Prioriti-
zation” menu.

13.6

VPN: Remote Access to the Home Network

Via a VPN (Virtual Private Network) a secure remote access to
the network of the FRITZ!Box can be established.

VPN in the FRITZ!Box

IPSec

VPN in the FRITZ!Box is based on the IPSec
standard.

Computer-LAN

Computer-LAN linkup: VPN connections can
be configured for individual remote com-
puters.

LAN-LAN

LAN-LAN linkup: VPN connections can be
configured for remote networks.

Eight simultaneous
connections

FRITZ!Box supports a maximum of eight si-
multaneous VPN connections.

«
...
73
74
75
76
77
...
»

Summary of Contents for Box 6490 cable














































































































































































Reviews:

No comments

Related manuals for Box 6490 cable

Brand: LaCie Pages: 44

LaCie Ethernet Disk

Brand: LaCie Pages: 2

5big - Network NAS Server

Brand: LaCie Pages: 9

Brand: LaCie Pages: 14

12big Rack Fibre 8

Brand: LaCie Pages: 9

VigorIPPBX 2820 Series

Brand: Draytek Pages: 29

Nighthawk M6 Pro

Brand: AT&T Pages: 2

ADSL/ADSL2/ADSL2+ Router 660R-6xC Series

Brand: ZyXEL Communications Pages: 282

Barricade SMC7901WBRA2

Brand: SMC Networks Pages: 2

RS-232/422/485 Serial Card CE 3PXCC4A

Brand: B&B Electronics Pages: 47

SLK-R602 Series

Brand: Seriallink Pages: 29

Brand: Supermicro Pages: 27

Brand: iDirect Pages: 72

Brand: Zhone Pages: 28

HFisolator 9730/26-11

Brand: Stahl Pages: 2

Brand: N-Tron Pages: 2

Brand: Aztech Pages: 13

Brand: Echelon Pages: 99

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands