background image

IMPORTANT SAFETY INFORMATION 

- Read this manual carefully before using your grill to reduce the risk of fire, burn hazard or other injury. 

- Extreme care should be used because of the high temperatures produced by this appliance. CHILDREN

SHOULD NOT BE LEFT UNATTENDED IN AN AREA WHERE THE GRILL IS BEING OPERATED. 

- This appliance must be kept clear from combustible materials, gasoline or other flammable vapors and 

liquids. Do not allow flammable materials to come in contact with grate, burner or hot surfaces. 

- Do not repair or replace any part of this appliance unless it is specifically recommended in this manual.  

A qualified service technician should conduct all other service. 

- Follow the installation and servicing instructions provided with this product.  Have your grill installed by a

qualified service technician.  Locate the main gas supply valve so that you know how to shut the gas off to
your grill. If you smell gas, make sure all gas connections are tight before operation. If you continue to smell
gas call a qualified technician. 

- When lighting the burners, always pay close attention to what you are doing.  Be certain you are pushing

the igniter to light the burners you intend on using. 

WARNING

If you smell gas:

1. Shut off gas to the appliance.
2. Extinguish any open flames.
3. Open lid.
4. If odor continues, immediately

call your gas supplier.

TESTED IN ACCORDANCE WITH ANSI

Z21.58a-1998/CGA 1/6a-M98 STANDARD
FOR OUTDOOR COOKING GAS APPLI-
ANCES.  THIS GRILL IS FOR OUTDOOR
USE ONLY.

Check your local building codes for the proper
method of installation.  In the absence of local
codes, this unit should be installed in accor-
dance with the National Fuel Gas Code No.
Z223.1 and the National Electrical Code

ANSI/NFPA No. 70

FOR YOUR SAFETY

DO NOT

try lighting this grill without reading

the 

“LIGHTING INSTRUCTIONS”

section of

this manual.

FOR YOUR SAFETY

DO NOT

store or use gasoline or other flam-

mable vapors and liquids in the vicinity of this
grill.

This appliance is not intended to be

installed in or on recreational vehicles or boats.

CALIFORNIA PROPOSITION 65 - 

WARNING:

The Burning of gas cooking fuels gen-

erates some by products which are on the list of sub-
stances which are known by the State of California to
cause cancer or reproductive harm.  California law
requires businesses to warn customers of potential
exposure to such substances.  To minimize exposure
to these substances, always operate this unit accord-
ing to the use and care manual, ensuring you provide
good ventilation when cooking with gas.

General Safety Instructions

Summary of Contents for Side Burner












Reviews: