background image

8

Operating Instructions

Operating Instructions

(continued)

CHECK FILTER FEATURE, YOU WILL SEE:

2009 Electrolux Home Products, Inc.

All rights reserved.

DO THIS:

PRESS FILTER 

RESET BUTTON

TIMER: DELAY STOP / START FEATURE

YOU WILL SEE HOW MUCH TIME IS CHOSEN:

FIRST

DO THIS:

PRESS

TIMER BUTTON

THEN

DO THIS:

PRESS

UP/DOWN BUTTONS

Note: This feature is a reminder to clean the Air Filter (See 
Care and Cleaning) for more efficient operation. The LED 
(light) will illuminate after 250 hours of operation. To reset 
after cleaning the filter, press the "Filter Reset" button and 
the light will go off.

Note: For Delay Stop, the unit must be in the On position

Note: For Delay Start, the unit must be in the Off position.
First, Press TIMER button, then adjust timer setting, tap or hold the UP arrow (     ) or the DOWN arrow (     ) to change delay 
timer at 0.5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time 
remaining until start (8, 7.5, 7, etc.). The Delay Start Operation automatically selects cooling with maximum Fan speed (if Cool, 
Energy Saver, or Fan Only was the last mode selected) . The temperature maintained will be the same as previously set. To change 
the set temperature, press "COOL" then Up or Down arrows until the desired temperature is indicated on the display. After 5 
seconds, the control will automatically change the display back to the hours remaining until the unit will start/stop. Pressing the 
unit On/Off button at any time will cancel the Delay Start/Stop function. The Delay Start/Stop Feature will work until the unit either 
starts or stops. Once that happens the above steps have to be repeated again. 

YOU WILL SEE:

Note:  This feature can be used with any combination of FAN 
Speeds (Low speed only on 115V models), Timer, or Sleep 
Modes. When in the "Heat" mode,the fan will run continuously 
while heat is needed. The temperature  will automatically be 
maintained anywhere between 55 °F(13 °C) and 80 °F(27 °C)
(The upper limit of temperature could reach 86°F(30 °C) on some 
of the 115V models.). When the room set temperature is satisfied, 
the fan will cycle off and on to circulate and sample the room air.

PRESS MODE BUTTON,

CHOOSE HEAT

DO THIS:

HEATING FEATURE:

Summary of Contents for LRA08PZU1














Reviews: