background image

1

UNPACKING AND EXAMINING
YOUR OVEN

Open the bottom of the carton, bend the carton flaps back and

tilt the oven over to rest on plastic foam pad. Lift carton off oven

and remove all packing materials, WALL and TOP CABINET

TEMPLATE, Turntable, and Turntable Support. SAVE THE

CARTON AS IT MAY MAKE INSTALLATION EASIER.

1. Remove the feature sticker from the outside of the door, if

there is one.

2.

DO NOT REMOVE THE WAVEGUIDE COVER, which is
located on the right side wall of the oven cavity. Check to

see that there is a Wall TEMPLATE and Top CABINET

Template. Read enclosures and SAVE the Operation

Manual.

Check the oven for any damage, such as misaligned or bent

door, damaged door seals and sealing surfaces, broken or

loose door hinges and latches and dents inside the cavity or on

the door. If there is any damage, do not operate the oven and

contact your dealer or ELECTROLUX AUTHORIZED SER-

VICER. See Installation Instructions for more details.

p/n

 316137

2

3

3

TINSEB386MRR0

Installation
Instructions

Over the Range
Microwave Oven

NEED HELP?

For customers in the United States, call: 1-800-944-9044 

For customers in Canada, call: 1-800-213-9397 (English) 
1-800-668-4606 ext.8199 (French)

READ CAREFULLY. KEEP THESE INSTRUCTIONS.

Safety door
latches

Hinges

Door seals and 

sealing surfaces

Oven Cavity

BEFORE YOU BEGIN

IMPORTANT

– Save these instructions for

local inspector's use.

IMPORTANT

– Observe all governing codes

and coordinates.

Note to Installer

– Be sure to leave these

instructions with the Consumer. 

Note to Consumer

– Keep these instruc-

tions for future reference.

Skill Level

– Installation of this appliance

requires basic mechanical and electrical skills.

Proper installation is the responsibility of the installer.

Product failure due to improper installation is not cov-

ered under the Warranty.

Please read all instructions thoroughly before installing

the Over the Range Microwave Oven. Two people are

recommended to install this product.

If a new electrical outlet is required, its installation

should be completed by a qualified electrician before

the Microwave Oven is installed. See 3 ELECTRICAL

GROUNDING INSTRUCTIONS on page 2.

Read these instructions completely and carefully. 

Summary of Contents for FMV156DB









Reviews: