Frigidaire FGBM19WNVDA, Installation Instructions Manual

Page: 21 / 26

Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting plate
touch the bottom of the cabinet when pushed
flush against the wall and that the plate is properly
centered under the cabinet.
CAUTION:
Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
3
4
ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate
through the holes designated to go into drywall
and reattach the toggle wings to
3 ⁄
4
″ (19 mm) onto
each bolt.
1
INSTALLATION OVERVIEW
Attach Mounting Plate to Wall
Prepare Top Cabinet
Mount Microwave Oven
Adjust Exhaust Adaptor
Wall
Mounting
Plate
Spacing for Toggles
More Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
Installation Instructions
2
OUTSIDE TOP EXHAUST
(Vertical Duct)
IMPORTANT NOTES:
•
Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
. Connect Ductwork
Check Damper Operation
Adapting Microwave Blower for
Outside Top Exhaust
C
C2.
C1.
C3.
C4.
C6.
C5.
C7
C1.
3/8" TO EDGE
NOTE: IT IS VERY IMPO
RTANT TO
READ AND FOLLOW TH
E DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING
WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template se
rves to position the bottom
mounting plate and to locat e the horizontal exhaust
outlet.
1. Use a level to check that the
template is positioned
accurately.
2. Locate and mark at least o
ne stud on the left or
right side of the centerlin e.
It is important to use at leas t one wood
screw mounted firmly in a s
tud to support the weight
of the microwave. Mark two
additional, evenly spaced
locations for the supplied to ggle bolts.
3. Drill holes in the marked lo cations. Where there is
a stud, drill a 3/16" hole fo
r wood screws. For holes
that do not line up with a
stud, drill 5/8" holes for
toggle bolts.
DO NOT INSTALL THE MO
UNTING PLATE
AT THIS TIME.
4. Remove the template fro
m the rear wall.
5. Review the Installation In
struction book for your
installation situation.
Locate and mark holes to
align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE
STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION
FOR 2 ADDITIONAL, EV
ENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Locate and mark holes to
align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE
STUD ON EITHER SIDE
OF
THE CENTERLINE.
MARK THE LOCATION
FOR 2 ADDITIONAL, EV
ENLY
SPACED TOGGLE BOL
TS IN THE MOUNTING PL ATE
AREA.
Trim the rear wall templat
e along the dotted line.
Trim the rear wall templa
te along the dotted line.
12"
4"
Darle vuelta a la hoja para consultar la
versión en Español.
EN-20