Frigidaire 242101800, Use & Care Manual

Page: 5 / 10

5
InStALLAtIOn
Reversing the door swing
The glass door can be opened from left to right and vice
versa. Should you desire to change the opening direction,
please follow these instructions.

nOtE
All parts removed must be saved to do the
reinstallation of the door.
Remove top cap. Remove the three screws that hold 1.
the upper hinge (right side) to the top of the cabinet.
See Fig. 1.
Carefully remove top hinge (See Fig. 1.), then lift the
2.
door up off of bottom hinge and place it on a padded
surface to prevent scratching it. See Fig. 2.
Remove the three button plugs from the upper left
3.
corner of the cabinet and transfer them to the holes
on the opposite side. Be sure to press the button
plugs firmly into the holes. See Fig. 1.
Remove three screws that hold the bottom hinge to 4.
lower end of cabinet. Remove the three button plugs
from lower LH corner and transfer to holes where
bottom hinge was just removed. See Fig. 3.
Unscrew pins from both hinges and transfer to
5.
threaded hole on opposite side. See Fig. 4. Re-install
bottom hinge in LH corner of cabinet using same
three screws removed in Step 4.
On bottom edge of door, transfer door stop bracket
6.
and bushing to holes on opposite side. See Fig. 6.
On top edge of door, transfer the button plugs and
7.
bushing to hole on opposite side. See Fig. 7.
Place bottom LH corner of door onto lower hinge,
8.
then install top hinge to cabinet. Make sure door
is level and it seals properly against cabinet, then
securely fasten three screws. See Fig. 7. Snap top
cap back onto hinge.
Chart 2
Step 7:Remove the bolt on the bottom of the door by screwdriver � (see chart
3)
Step 8:Remove the screw � and the block � ,then set them on the left side.(see
chart 3)
ľ
ļ
Ľ
Chart 3
Step 9:Change the hinge axis � from the right hole to left hole(see chart 4)
Ŀ
Chart 4
Step 10:Use knife to remove the parts � ,see chart 5.
- 8 -
Fig. 2
Screws
Top cap
Bushing
Hinge
� Handle
ĸ
Wooden Shelf Made of Beech
Ĺ
Control Panel
� Glass Door
� Control Switch of Lamp
� Adjustment Leg
Door Reversal Instructions:
You can reverse the door swing if you change the position of the hinge( � ) ,pls
follow the steps below:
Step 1:Close the door and use the knife carefully to remove the parts �
ǃ
� (see
chart 1)
Step 2:Remove the hinge cover
Ĺ
(see chart 1)
Step 3:Remove the screws by cross-screwdriver
ĺ
(see chart 1)
Step 4:Remove the top hinge
Ļ
(see chart 1)
Step 5:Remove the bolt by screwdriver
ļ
(see chart 1)
ĸ
ķ
Ĺ
ĺ
Ļ
ļ
Chart 1
Step 6:Open the door and lift it up carefully then remove it,see chart 2.
- 7 -
Button plugs
Step 11:Loosen the bolt � and bottom hinge �
ˈ
then replace the parts on the
left and right side
ˈ
then assemble the parts,see chart 6.
ĸ
ŀ
ĺ
Chart 5
Chart 6
Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see
chart 7.
ŋ
Chart 7
Step 13:Assemble the door on the bottom hinge �
ˈ
then reset the door bolt �
- 9 -
Fig. 4
Move pin to
opposite hole
(upper and
lower hinges)
Step 11:Loosen the bolt � and bottom hinge �
ˈ
then replace the parts on the
left and right side
ˈ
then assemble the parts,see chart 6.
ĸ
ŀ
ĺ
Chart 5
Chart 6
Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see
chart 7.
ŋ
Chart 7
Step 13:Assemble the door on the bottom hinge �
ˈ
then reset the door bolt �
- 9 -
Fig. 3
Button plugs
Screws
Hinge
Step 11:Loosen the bolt � and bottom hinge �
ˈ
then replace the parts on the
left and right side
ˈ
then assemble the parts,see chart 6.
ĸ
ŀ
ĺ
Chart 5
Chart 6
Step 12:Revolve the hinge axis on the bottom of the door to the left hole,see
chart 7.
ŋ
Chart 7
Step 13:Assemble the door on the bottom hinge �
ˈ
then reset the door bolt �
- 9 -
Fig. 5
Button plugs
Screws