background image

14

Issue

Check items

Solution

Odors 

comming 

from system 

Check for source of odor.

Eliminate the odor

and clean filter.

Check for inclimate weather or

excessive wireless signals.

Power unit down for 3 minutes

and try operation again.

Outdoor unit 

has mist/fog 

Is system operating in heating?

While in defrost unit may

discharge mist/fog until clear of

moisture.

Noise like

 there is water 

inside unit 

Did air conditioner just come on?

Noise is the sound of

refrigerant flowing inside the

system. Once stabilized

noise will discontinue.

Crackling 

sound 

Did air conditioner just come on?

Temprature difference between

plastic front and dicharge temp.

may be great once temprature

stabilzes noise will discontinue.

Service and Assistance

Air conditioner 

operates 

abnormally

1

2

3

Before  calling  for  service,  please  check  the  "Basic  troubleshooting"  section 

above. This may help you to find the answer to your problem, avoid unnecessary 

service calls, and save the cost of a service call if the problem is not due to the 

product itself. If you have checked the "Basic troubleshooting" section and still 

need help, below you will find a list of available services:

You can find the name of your local Authorized Service Provider by visiting our 

website at www.friedrich.com. 
If you require further assistance please call 

Friedrich customer support at 1-800-541-6645. 

Before calling please make sure that you have the full model and serial number, 

as well as the date of purchase of you equipment available. Providing us with this 

information will allow us to better assist you.

Summary of Contents for MRM18Y3J



































Reviews: