manualshive.com logo in svg

Fresenius Vial INJECTOMAT 2000 Anasthesie, Technical Manual

Share
Download
Fresenius Vial INJECTOMAT 2000 Anasthesie Technical Manual Download Page 37

NT 0928 Rev.A0

page : 33

3.1.3.10.1. Protocol modification: see operator’s guide.

Keys description:

 allows to increase a digit or a letter.

allows to decrease a digit or a letter.

enter  the outstanding value and goes to the next or comes back to protocol choice after entering the
outstanding value.

allows to select the character to be changed.

 

Used symbols:     = flashing.

   

   

> 

I

 < 

: Minimum value selection

.

: Default value

 

selection.

: Maximum value selection.

: Increment selection.

     

+  

: Fix increment.

   =  

: Variable increment.

              : Induction dose.

              : Sustaining flow rate.

              : Programmed bolus.

 

<<<

<<<

  Simple bolus.

Occlusion alarm.

 

Parameters to be enter for any new protocol:

Protocol name.

 Dilution.

 Weight.

 Induction dose.

 Maintain flow rate.

 Bolus dose.

 Simple bolus flow rate.

 Default pressure limit.

3.1.3.11. Flange detection mode: 

PArD

This parameter allows to activate or not the switch of detection of the flange of the syringe:

: switch activated.

: switch not activated.

>  <

>  <

Summary of Contents for INJECTOMAT 2000 Anasthesie



















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands