background image

User’s manual - Mik

V1.1

03/2020

4/8

1. Carton Contents

- 1 Dante™ Mik microphone base 
- 1 user manual

2. Connections

1) Connection of the microphone. 
Insert the microphone’s 3-pin male XLR plug into the 3-pin female XLR socket on the 
microphone jack. Once the plug clicks into place, the lever on the XLR socket on the 
microphone jack must be pressed to remove the microphone. Note: The phantom power 
required for the operation of a condenser microphone capsule is continuously present with 
a voltage of 24V. 
As a reminder, the wiring standard for the XLR socket is :
1: ground
2: + signal (hot spot)
3: signal - (cold spot)

3. Connection to a Dante

TM

 network

Connect the RJ45 jack to an Ethernet switch that supports at least 100 MBits/s (Fast 
Ethernet). The power supply for the microphone jack is provided directly via the PoE 802.3 
af standard cable.

3. Configuring a Dante™ Network
1) Start the Dante Controller software.
2) Wait until the devices visible on the network appear in the software matrix. Note: If a 
device does not appear, there are several possible reasons, including :
- the device is not switched on / powered 
- the device is in another subnet 
- the device cannot be synchronized with other Dante™ devices
 
For either of the two reasons listed last, the Dante™ device must be shown at least in the 
Network View under the «Device Info» or «Clock Status» tab. Stopping and then restarting 
the speaker could be a quick fix to the problem. Further information can be found in the 
Audinate Dante Controller manual.
3) From the Dante™ Controller menu bar, select «Device / Device View» or press the 
Ctrl+D key combination. The «Device View» window will appear.
4) From the drop-down menu below the menu bar, select the speaker to be configured.
5) In the third tab «status», various information about the device is available. 
6) Click the «Device Config» tab. If necessary, adapt the «Sample Rate» to that used in the 
Dante™ network (all devices must have the same sample rate in order to work together).
7) In the «Rename Device» field, it is possible to modify the name used for the device in the 
Dante network, for better identification. Confirm any modification by pressing the «Apply» 
button.
8) From the «Network Config» tab, you can change the network settings for the speaker’s 
Dante™ interface if necessary.

Summary of Contents for Dante Mik









Reviews: