FreeWave FGR2-PE Programming & Installation Manual Download Page 18 | Manualshive

Page: 18 / 23

background image

2201 Cantu Court Suite 215 Sarasota, FL 34232 Page 18 of 23

(941) 378-4242 (800-237-3928 Fax (941) 378-2765

Stewartsigns.com

Figure #22 Mounting the External Antenna

Figure #23 Installing the Bulkhead Connector

3.

For weather proof seal wrap external half of the bulkhead connector as well as 2 inches of
the base of the antenna in the Arlon Silicone Self-Fusing Electrical Tape. See figure #23

4.

Inside the sign screw the 10 ft. antenna cable to the bulkhead connector.

5.

Dress the antenna cable and screw the other end of the antenna cable to the transceiver.
Secure in place with nylon cable ties.

«
...
16
17
18
19
20
...
»

Summary of Contents for FGR2-PE
























Reviews:

No comments

Related manuals for FGR2-PE

Brand: Teac Pages: 17

Brand: Jensen Pages: 14

Brand: Jensen Pages: 2

Brand: K40 Pages: 2

Brand: Timex Pages: 8

Brand: Insignia Pages: 29

Brand: Hannlomax Pages: 2

Brand: Technika Pages: 20

Brand: Salora Pages: 21

Brand: Crosley Pages: 7

Brand: Ocean Digital Pages: 9

Brand: SOUNDMASTER Pages: 4

Brand: Radio Shack Pages: 24

Brand: NAVICOM Pages: 27

Brand: NAVICOM Pages: 30

Brand: Navico Pages: 54

Brand: Durabrand Pages: 8

Brand: Vertex Standard Pages: 51

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands