FreeWave FGR2-PE Programming & Installation Manual Download Page 1

Page: 1 / 23

2201 Cantu Court Suite 215 Sarasota, FL 34232 Page 1 of 23

(941) 378-4242 (800-237-3928 Fax (941) 378-2765

Stewartsigns.com

Programming & Installing the FreeWave Model FGR2-

PE for a Wireless RF MODEM Connection

NOTE:

JM Stewart utilizes an industrial 900 MHz RF Transceivers from FreeWave

Technologies, model FGR2-PE.

The FreeWave Wireless Transceiver (Model

FGR2-PE

) will arrive pre-configured

and installed inside the sign. It is not necessary for you to program these
Transceivers. Please skip to page 18 for installation instructions.

Programming the Transceivers

Start with the Transceiver that will be installed in your Building

Plug the Transceiver Ethernet Port #1 into either your computer (using an Ethernet
crossover cable) or a switch/router using a RJ-45 Ethernet cable. Connect the power
adapter to the radio and a 110 volt outlet.

You will need to assign your computer a static IP address on the same subnet to
access the radio. You can use

192.168.111.90

. See Figure #1.

Figure #1

Summary of Contents for FGR2-PE
























Search results

Summary of Contents for FGR2-PE

Reviews:

Related manuals for FGR2-PE

Brands by name

Popular brands

FreeWave FGR2-PE, Programming & Installation Manual

Search results

Summary of Contents for FGR2-PE

Reviews:

Related manuals for FGR2-PE

Brands by name

Popular brands