Freespirit 30517 User Manual Download

Page: 14 / 36

INTRODUCTION

IMPORT

ANT

PRECAUTIONS

ASSEMBL

BEFORE

YOU
BEGIN

TREADMILL

OPERA

TION

LIMITED

ARRANTY

TROUBLESHOOTING

MAINTENANCE

CONDITIONING

GUIDELINES

CENTERING THE RUNNING BELT

The running belt has been properly adjusted at the

factory before it was shipped. At times the belt can

move off-center during shipment. Before operating the

treadmill, make sure the belt is centered and remains

centered to maintain smooth operation.

CAUTION:

Do not run belt faster than 1/2 mph while

centering. Keep fingers, hair and clothing away from

belt at all times.

If the running belt is too far to the right side:

With the treadmill running at 1/2 mph, turn the right

adjustment bolt clockwise 1/4 TURN at a time (using

the supplied Allen wrench). Check the belt alignment.

Allow belt to run a full cycle to gauge if more adjustment

is needed. Repeat if necessary, until the belt remains

centered during use.

If the running belt is too far to the left side:

With the treadmill running at 1/2 mph, turn the right

adjustment bolt counter-clockwise 1/4 TURN at a time

(using the supplied Allen wrench). Check the belt

alignment. Allow belt to run a full cycle to gauge if more

adjustment is needed. Repeat if necessary, until the

belt remains centered during use.

Belt is too far to the right side

Belt is too far to the left side

TENSIONING THE RUNNING BELT

The running belt has been properly adjusted at the

factory before it was shipped. At times the belt can

move off-center during shipment.

CAUTION:

Running belt should NOT be moving during

tensioning. Over-tightening the running belt can

cause excessive wear on the treadmill as well as its

components. Never over-tighten the belt.

If you can feel a slipping sensation when running on the

treadmill, the running belt must be tightened. In most

cases, the belt has stretched from use, causing the belt

to slip. This is a normal and common adjustment. To

eliminate this slipping, turn the treadmill off and tension

BOTH THE REAR ROLLER BOLTS

using the supplied Allen

wrench, turning them 1/4 TURN to the right as shown.

Turn the treadmill on and check for slipping. Repeat if

necessary, but NEVER TURN the roller bolts more than

1/4 turn at a time. Belt is properly tensioned when the

slipping sensation is gone.

Summary of Contents for 30517





































Search results

Summary of Contents for 30517

Reviews:

Related manuals for 30517

Brands by name

Popular brands

Freespirit 30517, User Manual

Search results

Summary of Contents for 30517

Reviews:

Related manuals for 30517

Brands by name

Popular brands