Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 737 / 1374

background image

Port-Write Controller

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

16-97

When an error occurs and the Serial RapidIO error/write-port interrupt is not enabled, software
takes the following actions:

1.

Polls the status bits (IPWSR[TE]) to determines that an error has occurred.

2.

Polls IPWSR[PWB] to verify that the port-write controller has stopped operation.

3.

Clears IPWMR[PWE] to disable the port-write controller.

4.

Clears the error by writing a 1 to the corresponding status bit (IPWSR[TE]).

16.5.7

Hardware Error Handling

Table 16-41 describes the possible hardware error conditions and what occurs when they are
detected. The error checking level indicates the order in which errors are checked. Multiple errors
can be checked at an error checking level. When an error is detected, no additional error checking
beyond the current level is performed. Port-writes are processed in a pipeline. The first error
detected in the processing pipeline updates the error management extension registers. These error
condition checks are provided by the messaging unit. These check are in addition to the error
condition checks provided by the RapidIO port, as described in Section 16.2.10, Errors and
Error Handling, on page 16-25.

Table 16-41. Inbound Port-Write Hardware Errors

Error

Description

Reserved ftype

1

Error checking level: 1
Interrupt generated: Serial RapidIO error/write-port if LTLEECSR[UT] is set.
Status bit set: Unsupported transaction in the Logical/Transport Layer Error Detect CSR
LTLEDCSR[UT].
Queue Entry Written in local memory: No
Response status: No response.
Logical/Transport Layer Capture Register: Updated with packet.

2

Comments: Packet is ignored and discarded.

Reserved tt encoding

1

Error checking level: 1
Interrupt generated: Serial RapidIO error/write-port if LTLEECSR[TSE] is set.
Status bit set: Transport size error in the Logical/Transport Layer Error Detect CSR
LTLEDCSR[TSE].
Queue Entry Written in local memory: No
Response status: No response
Logical/Transport Layer Capture Register: Updated with packet.

2

Comments: Packet is ignored and discarded.

Large transport size in
small transport mode or
small transport size in
large transport mode

1

Error checking level: 1
Interrupt generated: Serial RapidIO error/write-port if LTLEECSR[TSE] is set.
Status bit set: Transport size error in the Logical/Transport Layer Error Detect CSR
LTLEDCSR[TSE].
Queue Entry Written in local memory: No
Response status: No response.
Logical/Transport Layer Capture Register: Updated with packet.

2

Comments: Packet is ignored and discarded. An error or illegal transaction target error response
is not generated.

«
...
735
736
737
738
739
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: GE Pages: 93

Brand: EAW Pages: 2

Brand: Barco Pages: 100

Brand: National Instruments Pages: 17

COMSPHERE 3800 Series

Brand: Paradyne Pages: 88

COMSPHERE 3800PLUS

Brand: Paradyne Pages: 5

Brand: Opengear Pages: 2

Brand: ZALMAN Pages: 9

PARTNER PC CARD

Brand: Avaya Pages: 4

Brand: National Instruments Pages: 130

Brand: Kontron Pages: 42

Brand: Idis Pages: 85

ZyXEL ZyAIR B-120

Brand: ZyXEL Communications Pages: 20

Brand: ZALMAN Pages: 7

Brand: Lanner Pages: 59

Vortex86SX VSX-6100

Brand: ICOP Technology Pages: 50

Brand: Wyse Pages: 8

ULTRIX-FM-NS-1RU

Brand: Ross Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands