manualshive.com logo in svg

Freescale Semiconductor MSC8144E, Reference Manual

The Freescale Semiconductor MSC8144E Reference Manual is a comprehensive guide for users of this high-performance semiconductor chip. This essential manual is available for free download on our website, providing detailed instructions and insights into utilizing the product's advanced features and capabilities. Don't miss the opportunity to enhance your experience with MSC8144E, download your manual now at manualshive.com.

Share
Download
background image

RapidIO Interface Basics

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

 

16-25

16.2.9

Software Assisted Error Recovery Register Support

PnLMREQCSR is only supported for recovery from Drain mode. Therefore, software should 
only write to this register when the port is in Drain mode. The proper sequence for recovering 
from Drain mode is as follows:

1.

Software ensures that link activity is stopped. This should include:

a.

Software polls for Port OK bit to be set

b. 

Software waits longer than the link time-out value

2.

Software generates a link-request/input-status to obtain the link-partner's inbound ackID 
value.

3.

Software changes the RapidIO port's outbound ackID to this value (if necessary).

4.

If the link-partner was hot-inserted, software changes the RapidIO port's inbound ackID 
to zero.

Note:

If software can guarantee that the link-partner will not attempt to forward any packets 
to this RapidIO port, then software can write the outbound ackID of the link-partner to 
match the inbound ackID of this RapidIO port. However, if the link-partner attempts to 
forward another packet while this write is still outstanding, and the ackIDs is already 
lined up, then the write actually causes the ackIDs not to match, and the link is not 
recovered.

5.

Software should cause the link-partner to send a link-request/input-status to ensure that 
the RapidIO inbound port is operating normally.

6.

Software clears the Failed Encountered bit or the Output Buffer Drain Enable bit; 
whichever one caused the Drain mode (thus clearing Drain mode).

Software is responsible for timing software generated link-requests. If the response valid bit is 
not set in some reasonable period of time, the software should write another request in the 
register.

When software writes PnLMREQCSR, software should make sure that PnLMRESPCSR 
successfully reads as set; otherwise, software may read a stale ackID status/link status later.

Note:

When the RapidIO port's outbound ackID is written by software using PnLASCSR, the 
inbound ackID is also written. Care must be taken to ensure that the inbound ackID is 
not written to an incorrect value. For example, PnCCSR[PL] could be set to prevent 
the inbound ackID from changing before PnLASCSR is written.

16.2.10

Errors and Error Handling

This section describes how the logical and physical layers detect RapidIO errors and respond to 
them. For details on the action of the SC3400 core when it is notified of any of these errors, see 

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Barracuda Networks Network Quick Start Manual preview
Network
Brand: Barracuda Networks Pages: 2
C4i U1000 User Manual preview
U1000
Brand: C4i Pages: 8
Telit Wireless Solutions HE922-3GR Hardware User'S Manual preview
HE922-3GR
Brand: Telit Wireless Solutions Pages: 113
Moxa Technologies PT-7710 Series Hardware Installation Manual preview
PT-7710 Series
Brand: Moxa Technologies Pages: 2
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Brand: ADTRAN Pages: 2
ICOP Technology Vortex86SX VSX-6100 User Manual preview
Vortex86SX VSX-6100
Brand: ICOP Technology Pages: 50
Aaeon FWS-7150 Manual preview
FWS-7150
Brand: Aaeon Pages: 57
Juniper NSM4000 Hardware Manual preview
NSM4000
Brand: Juniper Pages: 196
Adaptec Serial Attached SCSI (SAS) Expander Card Installation And User Manual preview
Serial Attached SCSI (SAS) Expander Card
Brand: Adaptec Pages: 26
ExtraHop 72 TB ESU Quick Start Manual preview
72 TB ESU
Brand: ExtraHop Pages: 3
ADLINK Technology AMC-7000 User Manual preview
AMC-7000
Brand: ADLINK Technology Pages: 34
Ublox USB-ANNA-B4 User Manual preview
USB-ANNA-B4
Brand: Ublox Pages: 11
Acqiris SA240P User Manual preview
SA240P
Brand: Acqiris Pages: 89
Jupiter RAM PACK Instructions preview
RAM PACK
Brand: Jupiter Pages: 2
Compaq BL10e - HP ProLiant - 512 MB RAM User Manual preview
BL10e - HP ProLiant - 512 MB RAM
Brand: Compaq Pages: 228
Canon VK-16 v2.1 Administrator'S Manual preview
VK-16 v2.1
Brand: Canon Pages: 288
ETAS ETK-S6.0 User Manual preview
ETK-S6.0
Brand: ETAS Pages: 64
Paradyne 9126 User Manual preview
9126
Brand: Paradyne Pages: 470

Brands by name

Popular brands

Load more brands