Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 718 / 1374

background image

MSC8144E Reference Manual, Rev. 3

16-78

Freescale

Semiconductor

Serial RapidIO

®

Controller

16.3.3.8 Programming Errors

Table 16-32 shows a partial list of programming errors that result in undefined or undesired
hardware operation.

16.3.3.9 Disabling and Enabling the Inbound Message Controller

When the message controller is disabled by clearing IMxMR[ME] the following occurs (see
Table 16-115, IMxSR Field Descriptions, on page 16-182):

1.

Queue full clears the IMxSR[QF] bit.

2.

Message-in-queue clears the IMxSR[MIQ] bit.

3.

Queue empty is set via the IMxSR[QE] bit.

4.

Message busy clears the IMxSR[MB] bit after all pending frame queue entry writes
complete.

Once the message controller is disabled, an error response is generated for all new message
packets. If the message controller is disabled before all of the message segments for a
multisegment message are received, a message request time-out must occurs and all pending
frame queue writes must complete before message busy clears (IMxSR[MB]).

Table 16-32. Inbound Message Programming Errors

Error

Interrupt

Status Bit Set

Comments

Reserved value of the message in queue threshold
(IMxMR[MIQ_THRESH]) or reserved value of the circular frame
queue size (IMxMR[CIRQ_SIZE])

No

No

Undefined operation
results

The message in-queue threshold is equal to the frame queue
size

No

No

Message in queue
interrupt occurs when
queue is full

The message in-queue threshold is greater than the frame
queue size

No

No

Message in queue
interrupt never occurs

Frame queue entry written to non-existent memory

No

No

Memory controller will
cause the interrupt and
update capture
registers. IMxSR[TE]
will be set due to the
internal error.

Message enqueue and dequeue pointers are not initialized to
the same value

No

No

Undefined operation
results

The dequeue frame pointer register is set incorrectly.

No

No

Undefined operation
results

Queue misaligned.

No

No

Undefined operation
results.

«
...
716
717
718
719
720
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

ShareCenter DNS-320L

Brand: D-Link Pages: 4

ARM Cortex-A9 MPCore

Brand: Dave Embedded Systems Pages: 67

Brand: PaloAlto Networks Pages: 2

Brand: vPipes Pages: 3

Brand: Omega Engineering Pages: 34

Open Standard Module RPX30 EVA-MI V1

Brand: iesy Pages: 9

Brand: ADS Technologies Pages: 21

ExtremeCloud Appliance E1120

Brand: Extreme Networks Pages: 219

Brand: Acces I/O products Pages: 13

Brand: Idex Pages: 4

4 Channel Fan Speed Control Module CLX-1FAN4

Brand: Crestron Pages: 1

300624 - Ethernet Disk NAS Server

Brand: LaCie Pages: 24

Brand: Paradyne Pages: 470

Brand: Wavecrest Pages: 3

FASTRACK M1306B

Brand: Wavecom Pages: 55

Brand: Popp Pages: 2

Brand: Krüger & Matz Pages: 68

Brand: FM Systems Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands