Freescale Semiconductor MSC8144E Reference Manual Download | Manualshive

Page: 171 / 1374

background image

CLASS Features

MSC8144E Reference Manual, Rev. 3

Freescale Semiconductor

4-3

4.1

CLASS Features

The CLASS modules implement the following features:

Non blocking, full fabric interconnect.

Full bandwidth utilization toward each of the targets.

Allows full pipeline when a specific initiator accesses a specific target.

Allows full pipeline when accesses are generated by one or more initiators to specific
targets.

Read transactions can have a maximum pipeline of 16 acknowledged requests before
completing the transaction toward the initiator.

Write transactions can have a maximum pipeline of 3 acknowledged requests before
completing the transaction toward the initiator.

Programmable priority mapping.

Programmable auto priority upgrade.

Address decoding for target selection and multi target demultiplexing:

— Programmable address space start/end registers per target, for flexible address

decoding (resolution of 4 KB). Not supported in the reduced configuration option.

— Fixed priority between address decoding results which allows overlapping address

windows and deduction of address windows.

Bank address interleaving is supported for ports 1-4 on CLASS0 (M2 Ports 0–3 are
interleaved every 256 bytes, meaning that address bits 9–8 provide access to ports 1–4 of
CLASS0)).

Per-target arbitration algorithm:

— 4 level prioritization
— Each level implements pseudo round-robin arbitration algorithm.
— Weighted arbitration
— Optimized data bus utilization mode

Programmable masking priority for starvation elimination.

Multiplexing the initiator buses according to the arbitration winner.

Atomic stall unit (ASU) for atomic operations per target (valid for M2 memory only).

Normalizing mode that splits non-aligned transactions according to the target capabilities
(maximal burst size, power-of-2 burst, burst alignment, full size burst, data-beat
alignment, wrap size)

Error detection and handling:

— The CLASS identifies illegal addresses; addresses that do not belong to any of the

address windows or fall inside the negative windows.

— The CLASS stores the illegal address, reports the error, and generates an interrupt.

Debug and profiling unit (CDPU) support.

«
...
169
170
171
172
173
...
»

Summary of Contents for MSC8144E































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MSC8144E

Brand: C4i Pages: 8

SISPM1040-582-LRT

Brand: Lantronix Pages: 2

Brand: Lantronix Pages: 7

Brand: XESS Pages: 23

Brand: SMART Pages: 15

Aquaduct 360 XT

Brand: Aqua Computer Pages: 28

ELC-LTTR240-TBP

Brand: ENERMAX Pages: 16

D-NVR4108HS-4KS2/L

Brand: Dahua Pages: 33

LL140 RGB Series

Brand: Corsair Pages: 30

Brand: Intel Pages: 20

Brand: Z3 Technology Pages: 83

Brand: Cognex Pages: 57

Brand: Yeastar Technology Pages: 2

Brand: Faroudja Pages: 17

Brand: Faroudja Pages: 17

Brand: NetApp Pages: 95

Brand: Cables to Go Pages: 12

Brand: Johnson Controls Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands