Freddy Superminor User Manual Download Page 9

FPQ41 Superminor Issue 1 

 

9

 

4

 

Operation 

This section describes how to set up and use the 
Superminor. 

 

The Superminor must be earthed. 

4.1

 

Moving the Superminor  

The Superminor has 2 handles and fixed wheels 
to allow you to move it to wherever it is needed 

(Figure 4-1)

To move the Superminor, lift the handles, and 
push the Superminor (in a similar manner to 
pushing a wheelbarrow) to where you need to 
use it. 

When the Superminor is in location, lower the 
handles so that the stand is on the floor. 

 

Figure 4-1: Freddy Superminor 

 

 

Take care when moving the 
Superminor. It can weigh up to 
210 kg when full. Make sure you 
are able to move the Superminor 
and get help if necessary. 

Note

  The quoted weight of the 

3 kW Superminor is with the 
tank full of water – liquids 
with different viscosities can 
alter the maximum weight. 

 

Before using the Superminor, make 
sure the stand is on the floor and is 
stable. The tank should be in the 
upright position to vacuum and in 
the tilted position, as shown in 
Figure 4-1, to discharge. 

 

4.2

 

Changing the filter 

 

You must fit a filter to the Superminor 
every time it is used. If one is not fitted, 
the machine may be damaged or will 
not work efficiently and the warranty 
will be void. 

Handles 

Stand 

Fixed 
wheels 

Summary of Contents for Superminor








































Reviews: