1
4
L Shaped Tube 8 1/4 in x 47 1/4 in (21 cm x 120 cm)
one end perforated
2
2
Straight Tube 53 in (134.6 cm)
metal snaps on both tapered ends
3
2
Straight Tube 36 7/8 in (93.7 cm)
metal snaps on both tapered ends
4
2
Straight Tube 48 in (1.22 m)
metal snaps on both tapered ends
5
2
L Shaped Tube 8 1/4 in x 31 1/2 in (21 cm x 80 cm)
both ends perforted
6
2
J Shaped Tube 12 1/2 in x 22 5/8 in (30.5 cm x 57.5 cm)
7
2
Straight Tube 35 1/2 in (90.2 cm)
metal snaps on both tapered ends
8
2
Bent Tube
22 7/8 in (58.1 cm)
9
1
Mesh Net
24 ft x 8 ft x 4 in
(7.31 m x 2.44 m x 10.2 cm)
10
6
U Shape Ground 8 in (20.3 cm)
Stake
11
40
Self-Stick Closure 8 in x 3/4 in (20.3 cm x 1.91 cm)
Strips
12
8
Hardware Set metal: screw/washer/wing nut
FIGURE 2B
1
RED TAB
RED TAB
BLUE TAB
BLUE TAB
2
3
4
5
6
7
8
9
10
11
12
1
2
3
5
6
7
8
2
4
1
1
3
6
7
8
1
5
4
FIGURE 2A
Figure #2
FRAME ASSEMBLY
Assemble all lengths of tubing shown in Figure 1. Be sure that each piece
is inserted completely. The ends of each tube insert tightly and is secured
when the press button of the tapered end pops through the adjoining
perforated tube.(Figure 2A)
Figure #1 FRAME COMPONENTS
Step Assembly Instructions
1.
Assemble the first set of tubes, parts 1 & 2 . This will create the
back base.
2.
Insert tapered tubes, part 4 , to the back base. The end with the
two holes needs to be attached closest to the back.
3.
Insert L shaped tubes, part 5 , as shown into the side base section
of tubes part(s).
4.
Insert tapered tubes, part 3 , into the upward reaching base. The
end with the two holes needs to be at the top.
5.
After assembling the second set of tubes, parts 1 & 2 , place
these on the two tapered sections, part 3 , to complete the frame.
6.
Assemble the two reinforcement sections by connecting parts
6 , 7 , & 8 . The J shaped section, part 6 , is the upper section
while the bent tube numbered 8 attaches to the base.
7.
Align the 2 holes from J tube with the two holes in tube 3 . Using
one set of hardware, insert the screws through the two sets of
tubes from the front. When the screw passes through the two tubes
place the washer on the screw then add the butterfly. Turn the
butterfly clockwise to tighten. Repeat with the 2nd set of hardware.
(Figure 2B)
8.
Align the two holes from the bent tube with the two holes in tube 4 .
Using one set of hardware, insert the screws through the two sets of
tubes from the base. When the screw passes through the two tubes
place the washer on the screw then add the butterfly. Turn the
butterfly clockwise to tighten and secure the tubes together. Repeat
with 2nd set of hardware.
6
3
PART QTY DESCRIPTION
