manualshive.com logo in svg

Franklin Fueling Systems UPP PIPING, Installation Manual

Share
Download
Franklin Fueling Systems UPP PIPING Installation Manual Download Page 10

8

D2

D1

150mm (6") 

min

150mm (6") 

min

300mm (

12

") 

min

150mm (6") 

min

150mm (6") 

min

D1

D2

D3

 

•  When laying duct onto a concrete base a 150 mm (6") thick bed of compacted sand should be laid on the 

concrete, below the duct. (The minimum amount of sand should be 50 mm (2") of compacted sand)

•  All beds should be laid so that the pipe will not dip or sag when it is installed.

•  Laying of pipe should start from the tank farm.

•  Any mechanical joints or compression fittings must be located within a containment chamber or sump or 

be adequately protected from the environment when used on buried vent lines.

NOTE:

 Refer to FFS manual 408001007 for information about the electrofusion process.

•  UPP

®

 pipe that is located between dispenser containment or that exceeds 12 m (39 ft) should be laid in a 

series of large snake-like curves and not in straight lines. Uncoiled pipe, when laid, will settle in a natural 

curve.

•  Generally any thermal expansion will be accounted for by following our guidelines for spacing, backfilling 

and ensuring runs are “snaked”. 

•  Pipes should be separated from each other by at least the diameter of the largest pipe.
•  If pipe-runs cross, they must be separated by at least as much backfill material as the diameter of the 

largest pipe or protected using at least 25 mm (1" ) of expanded polystyrene.

NOTE:

 If used above ground, UPP

®

 pipe should be protected against mechanical, climatic damage. Additional 

supports and anchor points may also be required. Check fire codes for proper installation. Also see the document  

"UPP

®

 Piping Above Ground and Marina Installations."

•  Mark positions on the tank access chamber/sump for penetration locations and install UPP

®

 seals.

BEND RADIUS

The UPP

®

 piping systems have a semi-rigid construction which gives both strength and flexibility. To achieve 

absolute minimum bend radius in cold conditions, use a heated trailer or equivalent to precondition the pipe. In 

the drawing below, “X” is the bend radius, the distance between the pipe axis and “+,” the center of the pipe's 

arc.

Summary of Contents for UPP PIPING

















Reviews:

No comments

Brands by name

Popular brands

Load more brands