background image

3.5. Recommendations

The adjustment of the stove has been made at the

factory and checked by your installer.
In case of trouble shooting, do the usual maintenance

operations.
If problem persists call your installer.
This room heater is a high heat producing appliance

and may cause severe burns if touched on the glass

front door, or on top directly over the burner -

KEEP

CHILDREN AWAY.
CAUTION

: Never light the burner if there is any amount

of oil in pot. Clean out oil before lighting.
Too much oil in pot may cause a racing : a very high

flame generating vibrations.

In case of racing :

Turn off oil supply.
Set dial to the “0" position until fire has decreased to

proper burn rate.
Do not overfire. If the unit or chimney connector starts to

glow you are overfiring.

3.6. Maintenance of the stove

Every week :

operate the de-scaling lever. Pull the

rod, then push the rod in rotating 360 degrees two or

three times (

CAUTION : The rod is HOT

).

Every 3 or 4 months :

Clean the burner completely.

-

Remove and brush off the parts of the catalyser, using

a soft bristle brush.

-

Loosen any carbon soot from the burner with a putty

knife, and vacuum clean. Ensure that the small air

holes are free of carbon.

At least once a year / End of heating season :

Clean

or replace the oil filters, the oil supply line and to

change the joint of the de-scaling lever (rep. A, fig. 15,

code 142889) by a professional installer.

To clean the filter of the float regulator :

-

Set the regulation knob in closed position “0".

-

Turn off the tankvalve or the valve of the oil supply line.

-

Raise the safety lever of the float regulator.

-

Place a small container (or a small rag) under the

regulator filter opening in order to collect the oil

contained in the regulator.

-

Remove the filter cover plate located under the

regulator (rep. 4, fig. 13, p. 9) with a screwdriver,

-

Remove the tubular filter from the regulator. Clean it

with oil using a soft brush, never a wire-brush.

-

Replace the filter in the regulator, install the cover

plate and secure with the screw.

Use a soft clean cloth to wipe the front glass when the

unit is running at a low burning rate.

DO NOT CLEAN

GLASS WHEN HOT.

When the main door (or the cover) is opened for

cleaning, the flame will be disturb, and turn to a yellow

flame. Clean quickly, but gently. Close the door, the

flame will return to a normal burning position.

Clean all the enamelled panels of the stove with a dry

or slightly damp soft cloth.

3.7. Removing the burner

-

Disconnect the feed line from the de-scaler nut,

unscrew the burner fixing nuts (figure 14).

When replacing the burner, tighten the nuts evenly and

connect the pipe so as to be airtight.

10

Technical manual “1091”

“Bourgogne” ref. : 174 10 56

Instructions for user

Figure 14 - Removing the burner

)

Figure 15 - The joint of the de-scaling lever

Summary of Contents for Bourgogne















Reviews: