background image

9

9

OPERATION OF BLOWER

Allow the engine to warm up for a few minutes.
FRADAN BB-70 can be run at any speed between an idle of 2800 RPM and maximum load speed of 7300 RPM.
The velocity of the air stream can therefore readily be controlled from a gentle breeze to a high speed blast mov-
ing at 210 MPH, which will move garden leaves, twigs, and other debris from lawns and paved areas.
Use a low speed to blow dry leaves from a lawn or flower bed.
Use a medium to high speed to clean grass and leaves from walks, patios, and driveways.
Use a high speed to move gravel, dirt, snow, bottles or cans from driveways, streets, parking lots, or stadiums.

• CAUTION

Do not point the blower pipe in the direction of people or pets. Always wear safety glasses and use a face filter
mask. Read carefully “Safety Rules and Precautions.”

OPERATIONS

ENGINE STARTING AND STOPPING PROCEDURES

• STARTING COLD ENGINE

1. Move the throttle lever to the half open position.
2. Give a gentle push on the primer pump repeatedly

(7-10 times) until fuel comes into the primer pump.

3.

Cold Starts:

Move lever to close choke position.

4. Pull starter handle until engine false fires (sputters).
5. Remove choke (excessive cranking with choke on

will cause flooding of engine making it difficult to
start).

6. Pull starter handle until engine starts.
7. Allow engine to warm up for a few minutes before

using.

• STARTING WARM ENGINE

1. If fuel tank was not run dry, pull starter one to three

times and engine should start. 

(DO NOT USE

CHOKE)

If fuel tank was run dry, after refilling repeat steps 2

through 7 in 

STARTING COLD ENGINE.

• STOPPING THE ENGINE

1. Move throttle lever to slow position. Wait a few sec-

onds to allow engine to cool down. Depress the
RED STOP Button 

(located on reverse side of throttle

lever)

until the engine comes to a stop.

Summary of Contents for BB-70















Reviews: